Unusual output stage in Hipro supply

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • japlytic
    Badcaps Legend
    • Oct 2005
    • 2086
    • Australia
    #1

    Unusual output stage in Hipro supply

    When I reverse-engineered a Hipro supply from a SC996-002 satellite receiver, I found the circuitry for the +5V and +3.3V rails is quite typical, but the circuitry for the other rails is rather unusual . The circuit I made is on http://www.eserviceinfo.com/download...SC996-002.html
    My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      ORIGINAL POWER SUPPLY BOARD
      7 Photos
      11-22-2024, 01:46 PM
    • sam_sam_sam
      Modification to a ZD-987 desoldering/soldering station using a external switching power supply
      by sam_sam_sam
      I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

      I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
      07-01-2024, 06:34 AM
    • dicky96
      L4973V5.1 Power supply giving too much output voltage
      by dicky96
      Hi guys
      This power supply is from an FM Radio transmitter

      It takes an input of 28V and should output some lower voltage. When I first looked at it I found that there is a zener diode D3 directly across the V out to ground and it was short circuit.

      I removed the Zener, there are no markings to determine it's correct value, and I don't know what Wattage it should be either, plus it broke in half. I took a photo comparing it to a 1N914 signal diode and a smaller zener which I have (which I think are 0.5W but I am not sure) and also a resistor so maybe someone can...
      01-15-2021, 06:29 AM
    • sam_sam_sam
      Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
      by sam_sam_sam
      I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

      One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
      03-31-2024, 02:12 PM
    • tester001
      PLP-60-48 Single Output LED Power Supply - "chirping" noise
      by tester001
      Dear Badcaps forum members,

      Hope that you are all well!
      I am a newbie on a mission to figure out the cause of the PSU making a "chirping" noise:


      Having searched for this symptom online I have found some indication that failed capacitors may be an issue. To help with the troubleshooting, I have tried to isolate the problem and disconnected the PSU from the rest of the device - the chirping remained.
      I have then found that the whole PSU (apart from a small add-on board) can be replaced, and there is even a datasheet for it: https://cdn.badc...
      12-06-2023, 06:39 AM
    • Loading...
    • No more items.
    Working...