Ineed bios for Inspiron 5567 -La-D801P

[halinka1125]

Re: Ineed bios for Inspiron 5567 -La-D801P

hoaca388 - Your file is better, battery code says 2 amber 7 white - LCD bad. I Connected HDMI - image was shown, but after strictly 38s power off (each time if I turn it on it is 38s), in bios error log shows unknown code 0x0000002f.

[hoaca388]

Re: Ineed bios for Inspiron 5567 -La-D801P

hoaca388 - Your file is better, battery code says 2 amber 7 white - LCD bad. I Connected HDMI - image was shown, but after strictly 38s power off (each time if I turn it on it is 38s), in bios error log shows unknown code 0x0000002f.

Maybe you should keep testing the hardware.

[halinka1125]

Re: Ineed bios for Inspiron 5567 -La-D801P

Hmm - maybe, it's strange that it's always 38 seconds - in the bios, when windows starts - always exactly 38 seconds(hot/cold doesn`t matter). Thermal shutdown not registered. Only events from LCD failure, and Unidentified System i about menu. I'll try to find out what's wrong.
THANK YOU VERY MUCH

[halinka1125]

Re: Ineed bios for Inspiron 5567 -La-D801P

OK. Some problems fixed
Bios from post not working, but i found one working <Clear me LA-D801P.bin>. Bios file from hoaca388 gave me a clue that not all in HW is ok. In test Bios chip after few flashes died <echanged from another mobo, new one from aliexpress gave me 3 orange and 5 white blinks but was programming itself good>. LCD Cable was OK, but fuse on LCD matrix was blown <on 3.3V line>, replaceing it <with same amperage rate fuse> was a bad idea:/ I got magic smoke from SY6288C20AAC - lerning from lesson - first short circuit test - then live test:P. On LCD matrix is U1 broken. So LCD is a trash, but all other things working now (there is no shutdown after 38s) . Thank You for help
PS. How to change ServiceTag in this platform?

[feqke0wq3]

Re: Ineed bios for Inspiron 5567 -La-D801P

OK. Some problems fixed
Bios from post not working, but i found one working <Clear me LA-D801P.bin>. Bios file from hoaca388 gave me a clue that not all in HW is ok. In test Bios chip after few flashes died <echanged from another mobo, new one from aliexpress gave me 3 orange and 5 white blinks but was programming itself good>. LCD Cable was OK, but fuse on LCD matrix was blown <on 3.3V line>, replaceing it <with same amperage rate fuse> was a bad idea:/ I got magic smoke from SY6288C20AAC - lerning from lesson - first short circuit test - then live test:P. On LCD matrix is U1 broken. So LCD is a trash, but all other things working now (there is no shutdown after 38s) . Thank You for help
PS. How to change ServiceTag in this platform?

Hello halinka1125, i have the same trouble with the LCD and the shutdown after 38 Sec. and the Log 0x0000002f.
Which fuse was defective in your case?
Can you give me a picture or the number of the fuse?
Thx

[halinka1125]

Re: Ineed bios for Inspiron 5567 -La-D801P

SMD Fuse (size 805) on LCD panel matrix electric board near connector, it is labeled F1 3.3V 1.5A 32V. But 38s shutdown means you have also bad bios...
Do check on external regulated power supply if Your fuse was blowed. On this matrix 19V and 3.3V pins are very close. I have replaced LCD cable for be 100% sure. Blowed fuse and damaged bios chip and U1 must died for some reason...
Good luck!

[ldinfortec]

Re: Ineed bios for Inspiron 5567 -La-D801P

Here

worked fine for me here. calling in 5 seconds

[halinka1125]

Re: Ineed bios for Inspiron 5567 -La-D801P

If anyone need zipped Clear me LA-D801P.bin . After replace LCD and flex my dell is 100% working.

[Chieftain]

Re: Ineed bios for Inspiron 5567 -La-D801P

Clear me LA-D801P.zip works fine for my Bios locked dell...
Thank you v much