1983 dump for surface pro 8

[pokyss1]

1983 dump for
surface pro 8.

thanks

[volinakis]

Re: 1983 dump for surface pro 8

1983 dump for
surface pro 8.

thanks

try

[pokyss1]

Re: 1983 dump for surface pro 8

try

tank you for your help but i had a problem saving the source file and there is a possibility of repairing the source and doing the unlock.

[Muhammad Faizan]

Surface Pro 8 bios password

[SMDFlea]

RULES UPDATE for BIOS requests/offers AVOID BANNING, READ BEFORE POSTING
https://www.badcaps.net/forum/troubl...before-posting

You MUST:

• Provide the full machine model number, serial number (or Service tag, SNID) and the board model number (see https://www.badcaps.net/forum/showthread.php?t=88758 ) ,The serial number, make, full model number, motherboard model and revision (except QR codes) must be written/typed at your request as per the rules. Not as a picture, part of the file name and so on.

[Alex Baños]

Hi there. My Surface Pro 8 show MS logo for a few secong and then shut off.
I managed to flash in SPI bios the .bin posted above and then I have access to UEFI settings but without touch and with uefi pass.
I have tryed to clean ME with MEAnalyer + FIT + CSME repository, but, finished in error buliding outimage.bin
Can anybody help me please? I would need Clean ME Region on my original bios
P.D Atached pictures with the problem
Tks a lot

Model Surface Pro 8 1983 128GB
s/n 0F018WR215101J

[minhdigital]

Hi there. My Surface Pro 8 show MS logo for a few secong and then shut off.
I managed to flash in SPI bios the .bin posted above and then I have access to UEFI settings but without touch and with uefi pass.
I have tryed to clean ME with MEAnalyer + FIT + CSME repository, but, finished in error buliding outimage.bin
Can anybody help me please? I would need Clean ME Region on my original bios
P.D Atached pictures with the problem
Tks a lot

Model Surface Pro 8 1983 128GB
s/n 0F018WR215101J

Send to you, try

[Alex Baños]

Tks a lot. Works quite fine. The system goes to Uefi mode perfectly, with touch pad functionally but touch screen no. And, curiosly, when I try to install W11, configuring boot for USB, in the first blue screen, leave to response the touch pad, and touch screen is not functional. I have triying to install W11 to explore the solution by windows update...
Any ideas?
Tks

[minhdigital]

Tks a lot. Works quite fine. The system goes to Uefi mode perfectly, with touch pad functionally but touch screen no. And, curiosly, when I try to install W11, configuring boot for USB, in the first blue screen, leave to response the touch pad, and touch screen is not functional. I have triying to install W11 to explore the solution by windows update...
Any ideas?
Tks

Try again !!

[sonic_electronic011]

Hi, can somebody help me, surface stuck on logo, wont enter bios setup.
I have tried to swap BIOS and ME Region directly from Hex editor, because FIT gives me error that could not parse CSE. I also swapped ssd but still same.
S/N: 0F011Y2214701J
Model 1983

[hoaca388]

Hi, can somebody help me, surface stuck on logo, wont enter bios setup.
I have tried to swap BIOS and ME Region directly from Hex editor, because FIT gives me error that could not parse CSE. I also swapped ssd but still same.
S/N: 0F011Y2214701J
Model 1983

Try

[sonic_electronic011]

Both files shows logo for 5 seconds then turn off

[Alex Baños]

Try again !!

Non functional. Don´t entry in UEFI.
Tks anyway.

[Alex Baños]

Send to you, try

Hi and tks a lot. The bin goes properly now, It was an error flashing spi bios.

[Q1999]

i have a surface pro 8 that lost the original bios
the customer took it somewhere and replaced the 128mb rom chip
as far as i know the original rom should be 256mb
is there any way to find the original rom.
sn:0F0003N212901J
Surface Pro 8 - i5/8/128

[mohamedelmasry]

please fix hang on logo ... 1983

serial : 0F00U74214301J