Dell Latitude 5501 LA-H182P wont power on

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • ARS
    Member
    • Mar 2013
    • 28
    • Slovakia
    #1

    Dell Latitude 5501 LA-H182P wont power on

    Board was water damaged with short on 13,5V power line.
    After celaning and removing short on board i have 5v, 3,3v, 1v, 1,8v but no reaction to power button. Its same if i use USB-C or normal power supply.
    No shorts detected (only CPU power is 1.2 Ohm, but thats OK i think) no other water damage found.
    Tried to flash BIOS, no change.
    After pressing power button i get orange light in front (no light on power button LED) as long button is pressed.
    Advice needed.
    TIA Matus.
    Tags: None
    • mon2
      Badcaps Legend
      • Dec 2019
      • 14731
      • Canada
      #2
      What is the voltage and current draw showing on the usb-c meter?

        Comment

        • ARS
          Member
          • Mar 2013
          • 28
          • Slovakia
          #3
          Current draw is nly 0,03A, without change after pressing power button.

            Comment

            Previous template Next

            Related Topics

            Collapse
            • hoarderteks_kyriakos
              Dell Latitude E5570 - No display, turns off after a minute of pressing the power button.
              by hoarderteks_kyriakos
              Hello.

              Yesterday my mother encountered a problem with her laptop, which led to it not turning on and expressing the behaviour mentioned in the title (you press the power button and then it turns off after a minute)

              Here is what happened:
              At one point i was fixing a setting on the laptop to make the laptop properly recognize the NVMe drive i put in months ago. All worked until all of a sudden the computer blue screened. The screen said it would reboot, but it never did. So she held down the power button, powering it off. Pressing it again, the screen briefly turned...
              10-08-2025, 07:33 AM
            • dlonely94
              Dell Latitude 5591 not power on
              by dlonely94
              Hi everyone!
              I have a Dell Latitude 5591. It has a strange problem:

              First, when the WLAN card is plug in, it will not power on when press power button, even all voltage is up (19v, 3v, 5v, 3valw, 5valw)

              When I remove the WLAN card, it will start nomarlly. Then I power off and re-insert the WLAN card, it still work normally.

              But, if I left it for 3 or 4 days without the battery and adapter plugged in, it will not power on, and I have to repeat the above sequence.

              Sometime, when it not power on, I just unplugged the battery and adapter, wait...
              10-13-2024, 10:29 AM
            • imedbox
              Dell Latitude 5440 no power on
              by imedbox
              ihave the same probleme the labtop want charge with the power supply! my bat is decharged then i can test it with battry it power on!
              i got this after flash bios "XM25QH256C" for removing admin password,i revert to the original then not charge or power on, befor it power on and chargin!
              Any Help !

              her link for Boardview and the Schematic
              Dell Latitude 5440
              bios version : 1.12.20
              MTHERBOARD : IDB40 LA-M401P Rev:1.0(A00) 2023-11-10

              https://www.transfernow.net/dl/20250721QpvcJ0UG



              ...
              07-21-2025, 03:03 AM
            • NADJIB
              Dell Latitude 7390 _DAZ20 LA-F312P 1.0 - all power rails up except VCC_CORE and VCC_GT
              by NADJIB
              Hello,
              I need help please​

              I have Dell Latitude 7390, LA-F312P 1.0


              - power LED turns on a few one second or two withe power supply or battery
              - the power supply indicate current 0.16 A While laptop is powered
              I checked:

              While laptop is powered from battery/barrel plug AND power LED is on, all voltage rails show up, except +VCC_CORE and +VCC_GT.


              * COIL
              PL612
              - Output resistance to ground is 14.7 ohm.
              PL613 AND PL610
              - Output resistance to ground is 9.8 ohm.
              1 Photo
              01-23-2024, 04:31 PM
            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              ORIGINAL POWER SUPPLY BOARD
              7 Photos
              11-22-2024, 01:46 PM
            • Loading...
            • No more items.
            Working...