6800XT artifact on benchmark and crash

HelpMeRepair

Senior Member

Join Date: Jun 2022

Posts: 62

Country: Canada
#1

6800XT artifact on benchmark and crash

11-05-2024, 09:41 AM

Hi guys , thanks for the help and hint in advance

I have a 6800XT that is detected , but im not able to memtest it ( says it cant buffer )

if i try to benchmark it , it goes artifact and crash after few seconds.

anyone have a clue ? thanks !

card is a AMD FE 6800XT , and any hardware mem guide checkup can help if you have any tuto too !😀

edit : component looks good after visual inspection .
Tags: None

Previous template Next

Satellite r945-p440 - Hard crash coming out of sleep

by cappernicus

Toshiba Satellite r945-p440
Motherboard: FAM2SY2 A3256A
I do not have a schematic or board file

I usually let it go to sleep every time I use it because it is nearly always plugged in, with occasional shutdowns to reset things. Then it started to hard crash every time it tried to come out of sleep. The lights would come on for half a second but before anything shows on the screen they would all shut off and it would boot up as if I had shut it down completely (except that windows knows it didn't), and when it comes back on the fan ramps up to full and stays there perpetually...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
04-16-2025, 05:31 PM
6800XT Red Devil

by Benass

Hello.
Looking for some help mainly to read schematics and understand posible reasons for missing signals.
GPU in question is 6800xt red devil.
It was artifacting to begin with, Tserver memtest's no faults found. Put card on shelf for 6 months. started troubleshooting again last week and card is totaly dead.

12V rail
5V rail
3.3_AUX and thats it.
1.8V_S5 missing and no other voltages.
I dont have Enable signal for 1.8v
Schematics and boardview attached.

Can any one advice me on what signals should i investigate. ? Thank...
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
01-25-2025, 03:57 AM
GB RTX2080 Super - crash on load > second switched 12V instability > what is purpose of this circuit?

by ktmmotocross

Hello.
Have this GB 2080 Super that crash on load. When half load i see instability on one of two switched 12V rails. I dont know its purpose and dont have BV or Schema for this board.

Can anybody explain me what is purpose of this two switched 12V lines?...
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
10-03-2024, 12:22 AM
Lenovo M90q Gen 4 Problem Bios crash update

by Nozle Gmail

Hello,

I have a Lenovo M90Q Gen 4, with Intel 13500.

Yesterday, the BIOS was updated to the latest version, and for some reason, the process failed. Now, the computer displays nothing on the screen, and approximately 20 seconds after turning on, it immediately shuts down again.

I tried copying the USB BIOS from Lenovo's website to a FAT32 USB drive and setting the motherboard jumper to CMOS mode (pins 2 and 4), even though the manual indicates maintenance mode, but I haven't found any jumper with that name.

When I insert the USB drive and set...
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
05-31-2025, 08:28 AM
RTX 3070Ti works normal, but when let 10min to work on full it crash

by ktmmotocross

Hello.
I have few RTX 3070Ti that works for hours on 90% of TDP, but when pushed to 100% tdp it crash in 10-15minutes. Cards was repasted and repaded, but still the same. Do u think that reball wil help?
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
05-07-2023, 12:24 AM
Loading...
No more items.

6800XT artifact on benchmark and crash

6800XT artifact on benchmark and crash

Related Topics