HP lp3065 repair or part source.

[KhitSicker]

Re: HP lp3065 repair or part source.

It is flux residue. I was told this was refurbished unit.

[retiredcaps]

Re: HP lp3065 repair or part source.

left pin was 0. middle was 3.3 and right was 5.3

Okay, these readings make more sense and correspond with the datasheet. The voltage regulator is good.

The main Novatek chip looks like it has some left over flux residue. If it is not flux residue, then the chip doesn't look too healthy.

[KhitSicker]

Re: HP lp3065 repair or part source.

left pin was 0. middle was 3.3 and right was 5.3

[retiredcaps]

Re: HP lp3065 repair or part source.

Using the middle pin for the black probe I am getting 3.3 from the left one and 1.8 from the right.

I normally use a ground screw for my black probe (for ground). I suggest you do the same.

Use a ground screw on the logic board and retest all 3 pins and repost.

[KhitSicker]

Re: HP lp3065 repair or part source.

ah my mistake. Using the middle pin for the black probe I am getting 3.3 from the left one and 1.8 from the right.

[retiredcaps]

Re: HP lp3065 repair or part source.

Im getting 5.5 out of i301... Guessing that means I have some bad caps on the board?

Please list the voltages on all pins of 1084-33.

The datasheet at

http://pdf1.alldatasheet.com/datashe...-33ZC-TUL.html

says the middle pin is Vout and pin 3 is Vin.

If you are truly getting 5.5V DC on Vout, then the regulator itself should be replaced.

[KhitSicker]

Re: HP lp3065 repair or part source.

Okay, getting 5V SB is good.

On the logic board there is a voltage regulator 1084-33 (I301). Verify that you are getting 3.3V DC output.

Im getting 5.5 out of i301... Guessing that means I have some bad caps on the board?

[retiredcaps]

Re: HP lp3065 repair or part source.

on the output on the left hand side the 5vsb was reading at ~5v

Okay, getting 5V SB is good.

On the logic board there is a voltage regulator 1084-33 (I301). Verify that you are getting 3.3V DC output.

[KhitSicker]

Re: HP lp3065 repair or part source.

The mosfets tested good. The 24v pins were reading at ~1.3v all others were 0. on the output on the left hand side the 5vsb was reading at ~5v and the 24v was ~1.3. I think the issue is in the logic board.

[jetadm123]

Re: HP lp3065 repair or part source.

Also, a lot of the larger screens seem to have probems with the inverter. Since the power supply has been replaced, try checking the fuse on the inverter. It's below the power connector and marked 10A/125V. If it's bad, try checking the 4 mosfets in the upper right of the inverter marked QXX (can't read it off the photo) for shorts. They are the 3-legged devices with the middle leg cut off.

[retiredcaps]

Re: HP lp3065 repair or part source.

On the power board, the lower right hand corner has a legend that says OUTPUT 24V and 16V. These are your secondary voltages.

With respect to ground, measure the DC voltage of each connector pin (be careful not to short out the pins), and report the voltages for each pin.

If all the voltages are 0V DC, then check the DC voltage across the largest capacitor (450V 180uF). Careful, this is high voltage. It should be around 165V DC if you are in North America.

[KhitSicker]

Re: HP lp3065 repair or part source.

Pictures as requested.

[jetadm123]

Re: HP lp3065 repair or part source.

Also, please a photo of the inverter board.

[KhitSicker]

Re: HP lp3065 repair or part source.

Camera is charging now, I'll post some pics as soon as I can. I do have a multimeter .. its kind of a crappy radio shack one though. There are some suspect soldier joints on logic board howeever i dont see anything that would constitute bad caps.

[retiredcaps]

Re: HP lp3065 repair or part source.

Also, you will need a multimeter to do some troubleshooting on this unit.

[jetadm123]

Re: HP lp3065 repair or part source.

Please post some clear focused photos of the power and logic board using the "manage attachments" button. Difficult to suggest tests if we can't see what you're seeing.

[KhitSicker]

I have a lp3065c hp p/n EZ320A which is not turning on. I have already replaced the power supply so I know its not that. I do not get any lights when its plugged in or if I hit the power button. One interesting thing though if I leave a usb thumb drive in the hub then plug it the power i get the drive access light for half a second on the thumb drive.

At this point I am thinking it is the lcd logic board. I have tried in vain to get an official part number from hp but it is not available on part surfer or from their tech support. I did search ebay and google for every number that was on the logic board but no luck. I was only able to find the part on this site http://www.shopjimmy.com/tvs/5057767-7330-vga-input.htm but they are out of stock. Again searching for that part number yields no results.

Does anyone know how to locate the official hp part number for this part or to repair it.