Allen&Heath XONE92 DJ mixer repair

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • JohnsonJ
    Member
    • Dec 2020
    • 12
    • Slovenia

    #21
    Re: Allen&Heath XONE92 DJ mixer repair

    Hello everyone, just a quick question before I proceed with the pot replacement:

    For HiFi gear, is solder with 60% Lead/40% Tin content suitable, or should I hold off on the replacement until I get a more suitable solder of Silver/Copper/Zinc ?

    Comment

    Related Topics

    Collapse

    • eum
      PSU Board repair or replacement Ecler Nuo 2.0 DJ mixer
      by eum
      Hi,
      I try to repair this fly-back type PSU, I diagnosed (identifiable) dead N-MOS and fuse, but there are 3 smd resistors on the bottom that burned and became unreadable.

      The support in charge of the brand in France managed to get me the schematics from Ecler, but it didn't include the PSU board. After a while they finally told me that the unit was too old so they don't have the PSU board schems.

      I can find replacement PSU board online, but only for the Nuo 3 or 4 or 5, and it seems they ar compatible with each other, as I often find boards compatible with these...
      07-28-2023, 03:05 PM
    • TomGJ
      Genelec 8020C Bad capacitor
      by TomGJ
      Hi All, So I have two Genelec 8020Cs that are about 10 years old, one of them stopped switching on. I took it apart, fuse was blown, and I've traced the short to one of the two large capacitors on the circuit board.

      Now from looking at the Capacitors, they seem to be from Samwha's SD Series with the following specs: 3300uf, 35v, 85C, 25 x 16 mm Radial.

      The problem is, I can't find any capacitor from Samwha's SD Datasheet that matches these specs. The closest is 3300uf, 35v, 85c but 31.5 x 16mm, with a max ripple current of 2.5A. I'm guessing the 25mm is custom made for...
      11-02-2024, 07:45 AM
    • Bektronics
      Schematic Digital Audio mixer RCF type M18
      by Bektronics
      Hello dear audio friends.

      I am feverishly looking for the full electronic schematic (not a block diagram) of the RCF type M18 digital audio mixer.
      The device does not make a WIFI connection with my Apple tablet and yet I have already installed the recent app on it.
      I suspect that there is a problem in the mixer itself with the WIFI card and of course I would like to see this on an extensive schedule before opening the device.
      Thanks in advance if anyone can help me with this schematic.
      Of course, all information about this digital mixer and possibly references...
      07-24-2023, 06:40 AM
    • Transformer man
      Fader replacement on 1980s mixer - help with this schematic
      by Transformer man
      Hi - I am looking to replace faders on a mixing desk from the early 1980s. They are tired and worn. I'm new at looking at schematics and would really appreciate your help and expertise on replacements.

      The current faders are 88mm long with 60mm fader movement and are 10K B (which I think is a linear fader). They have been swapped out at some point (tell tale signs of additional screw holes a few mms below the top screw hole).

      I think the schematic suggests 5K B faders (but as a newbie I'm not sure if I am even looking at the correct part of the schematic!?). I have...
      04-22-2023, 04:13 AM
    • reformatt
      Macbook Air M2 A2681 Kernel panics after screen replacement
      by reformatt
      Just had a customer bring in a M2 MBA A2681 that had had a screen replacement in April at another repairer. Since then, she has been getting intermittent kernel panics. It's an aftermarket screen, and of course it fails in diagnostics as the calibration hasn't been done. The error in the panic log is "No device added after powering on the rails".

      It seems the original repairer has swapped the board and the screen to other MAC's, and said that it isn't a screen issue. From what I understand, by doing a quick search on Google, this is in fact a screen issue. The panic relates...
      07-31-2025, 08:37 PM
    • Loading...
    • No more items.
    Working...