Kettler M-9816, I am looking for serial eeprom content.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • warsztat
    Senior Member
    • Feb 2017
    • 189
    • Polska
    #1

    Kettler M-9816, I am looking for serial eeprom content.

    Hello, Kettler training device, no resistance control, incorrect speed indication. The error is in the control panel, I am looking for the contents of the serial eeprom memory indicated in the photo.
    24LC04B. The memory contains the device configuration.​



    Attached Files
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • SidneyCanadas
      93C46 and 93C56 EEPROM
      by SidneyCanadas
      I tore apart my instrument cluster for my 2008 Toyota Corolla made in 2007 in Cambridge, Ontario, Canada and pcb location: IC6=EEPROM is a surface mounted device with part # of 93C46W7, some claim the EEPROM out of a Camry part # 93C56 will allow odometer to roll over 299 999 KM or miles. The data sheet for both is below:

      https://cdn.badcaps-static.com/pdfs/...c6e42b20d3.pdf 2

      Anyone know if the Camry one will work on my Corolla?. And which EEPROM reader/writers do you all recommend I purchase that will allow me to read the old values of the old...
      06-14-2023, 01:16 PM
    • Yanleb
      LG 60PK550 Logic Control Board EBR63450301
      by Yanleb
      Hi all, I just want to share the repair of my 60PK550-UA TV set.

      The TV set was powering on, just no image. After verification, nothing wrong on the YSus or ZSus boards. Nothing wrong on the main board either.

      But I noticed that the LED was not flashing on the Logic Control Board. This is an EBR63450301. The LED is supposed to flash even with all the flat cables disconnected, with only the power cable attached.

      All the voltages measured at the electrolytic capacitors on the board were good. From top left to bottom right:
      C57: 3.30V
      C61:...
      07-20-2023, 12:38 AM
    • dmccul2698
      Pioneer DEX-P99rs "No EEProm " diagnostic code.
      by dmccul2698
      Hello, My head unit developed strange behaviors so I ran the built-in diagnostic package which returned "No EEProm". The service manual says there is no EEProm connected. I approached Pioneer and they said to swap out the DSP board. All said and good but the DSP board is $860 USD. I am hoping someone can help me

      1). Understand the schematic and check the connections between the EEProm and DSP
      2). Check the functionality of the EEProm

      I don't know if this is the unit's problem but it's a place to start.

      I have little to no electronic experience...
      6 Photos
      04-08-2024, 05:32 PM
    • Grouickman
      Hofmann geodyna 6300 Wheel balancer
      by Grouickman
      Hi there,

      First, I'm not sure it's the right section to post for this type of device, but could not think of something better.

      Ok, so my son (a mechanic) bought a faulty Hofmann Geodyna 6300 wheel balancer (which appears to be mostly a re-branded Snap-on wheel balancer).

      I'm looking for any resources (doc, manuals, schematics) that would be available for this device or anyone that would have any knowledge on this particular device (or its Snap-On equivalent).

      I'm trying to diagnose the fault(s ?), but I can't find any schematic (appart from the...
      03-31-2025, 05:29 AM
    • hell
      Hıkıvısıon serial problem
      by hell
      Hello, I would like to talk about the problem. My Hikvison recording devices have a password, so the BIOS is written. Our problem is the serial numbers on the devices, as written, it works in offline mode, but I cannot change it to online mode in any way. I have the BIOS. I tried to edit it, but it could not find the serial number with the BIOS hex editor. I have the original serial numbers. Can you help me? Best regards.

      model DS-7208hqhı-K1
      main kod : ds-20899_P rev:2.0
      07-23-2025, 01:20 AM
    • Loading...
    • No more items.
    Working...