Video Editing That Allows Adding Lines and Objects

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • JonathanAnon
    Badcaps Veteran
    • Jul 2012
    • 457
    • Ireland
    #1

    Video Editing That Allows Adding Lines and Objects

    Hi Guys,

    I'm looking for software that will allow me to put in text, arrows and shapes for tutorial and demonstration. Of all the free video editors I have tried the only ones that have the ability to add lines and shapes are VSDC and Power Director.

    I want to put together tutorials and point to things and put in values and the like. I've settled on VSDC. Does anybody in the community have an objection to my decision?



    thanks,
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • joelz
      pin Setting parameter line or set lines menu for adding ITE5571e on RT809F programmer
      by joelz
      Hi, sorry if i here to request if anyone know number of pin to set lines for reading ITE7751e on RT809F..i try to see on schematic but i dont know how to choose it..pleasee..
      11-18-2024, 06:02 AM
    • Stanley1843
      Screen Display Vertical Multicolor Lines
      by Stanley1843
      Hello, I have a screen in where sometimes when I open it pop-up vertical multicolor lines (I would say the most of them are green). If I tun off and turn on the screen the lines dissapear or if I leave open the screen after approximately five minutes the lines gone. I measured the below voltages on the main PCB and on the T-CON board and the voltages are the same when it doesn’t display the vertical lines and when it displays the vertical lines. Also, I cleaned all the connectors very good with IPA. I moved back and forth the connectors and the COF tabs but the vertical lines didn't displayed...
      06-29-2024, 11:54 AM
    • jeyoung12
      Samsung QN50Q60t lines on screen
      by jeyoung12
      Hi all
      I have lines on the screen...which is an age old problem that can be remedied by watching Youtube videos and getting out the tape.
      My issue (after successfully fixing a different sammy tv with a separate tcon board and isolating the side of the panel...):

      This tv has an integrated tcon...so it is a bit more confusing when trying to isolate the clocks.
      It has a c ribbon and i have taken each end out to see if that will isolate the lines. instead, it makes it much worse ALL over the tv!

      So....i don't know what end of the C ribbon to work with...
      02-26-2024, 10:38 AM
    • howardc64
      TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
      by howardc64
      All left and right refers to looking from rear of TV (or looking from front with TV upside down)
      • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
      • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
      ...
      07-24-2025, 05:17 PM
    • Rubenlily
      Samsung QE50Q67TAU - horizontal lines
      by Rubenlily
      Hello,

      First of all I'm new here. While looking I found this amazing forum and I'm very happy I did. Now for my problem:

      I picked up a Samsung UHD QLED QE50Q67TAU from 2021 for $50 knowing it was defective. The seller said it had black lines and that it could get stuck in boot randomly.

      I've tried a new power cable, hard reset, opening up and jiggling all cables, pressing everywhere to see if I get a reaction but I've gotten nothing. I've tried the tape method but I've only managed to get the lines worse.

      I'm no expert but I've done the tape...
      08-16-2023, 01:12 PM
    • Loading...
    • No more items.
    Working...