Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
I try use AMIBCP but there I do not see DIMM enable/disable options it's looks that disable onboard memory via BIOS modification no possible. Maybe anyone can help disable memory with resistor straps?
-
S/N: N1NTCX00158403H
Full name: ROG Zephyrus G15 GA503RM
Motherboard: DAONJPMBADO REV: D
Original BIOS with onboard RAM enabled in attachment....
Leave a comment:
-
Hi everyone!
It is possible to disable onboard RAM with BIOS for this laptop? Motherboard is Quanta NJP
Leave a comment:
-
Please repair BIOS. No backlight, two beeps, keyboard not working
Model: IdeaPad 5 15ALC05-82LN
S/N: PF41ESZ7...
Leave a comment:
-
Lenovo IdeaPad 5 15ALC05
NM-D701
MTM: 82LN00M7PB
SN: PF3LRYL1
Please repair BIOS no display
Previous bios dump was not correct, please repair this one original from device...
Leave a comment:
-
Lenovo IdeaPad 5 15ALC05
NM-D701
MTM: 82LN00M7PB
SN: PF3LRYL1
Please repair BIOS no display...
Leave a comment:
-
-
Lenovo ThinkPad L15 G2
Serial number PF-3JQQY6
Type 20X3-00GMMH
Motherboard NM-D271
Please repair BIOS, all power is OK no display...
Leave a comment:
-
Re: Fujitsu Lifebook E544
Check resistance on coils near this chip...
Leave a comment:
-
G6-1169ea (R18D) low +VCORE
Hi everyone,
I have G6-1169ea (R18D) with low +VCORE, just 0,4V instead of 0.77V. Can anyone explain how to troubleshoot this?...Last edited by Artuha; 08-11-2020, 02:53 AM.
-
Re: Motherboard LA-9105P, no CPU power, 7 beeps
QZ11 have two resistors RZ18 (one side 19.8V other 15.4V) and RZ21 (one side 15.4V and other ground) UZ1 are open and make +1.5V from +1.5VS
I do not have idea how 5V can be on resistors, but I'm newbie in electronics and may be wrong. See 1.jpg and correct me if I'm wrong.
About PU400 - on PL400 I have 1.8V - in my opinion PU400 works as expected.
QZ1 also works Gate 19V source and drain 5V...
Leave a comment:
-
Motherboard LA-9105P, no CPU power, 7 beeps
Hi everyone,
Have LA-9105P motherboard with no power on +VCC_CORE, resistance 4 Ohms.
Both BIOS firmwares (4MB and 2MB) was re-writed.
PCH_PWROK are OK 3.3V
VR_ON OK 3.3V
After board turn on SLP_S5#, SLP_S4# and SLP_S3# the signal level rises to HIGH and immediatly fall to LOW.
Cooler keeps running and voltages stay on it's work values.
Post card connected to 30 and 31 pins of kb9012qf no POST codes.
CPU PWM controller ISL95833 was replaced without results.
PCH and CPU are cold. May...Last edited by Artuha; 03-27-2018, 03:58 AM.
-
Re: HP Pavilion Notebook - 15-ab127ca (Touch)
Hi,
This schematic is not applicable to Your board?...
Leave a comment:
-
Re: New Members - please post your introductions here
Hello all
Leave a comment:
-
No activity results to display
Show More
Leave a comment: