Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Hello guys, Good news !!Finally i found the problem on the ( ird sensor led ) Look what I discovered, unbelievable!!!I already doing my best to fix it and everything works just fine!!I what to say thank you all of you for the right guidelines !! Im honoured to be part of this beautiful community!!!!I 👍💪6 Photos
Leave a comment:
-
Hi my friend just told me the model (ice maker gsn-z1)
I have all the voltage there but after a press the bottom (start) in 5/10 second it stops .. Yea the capacitor are replaced already Two of them where a bit dead but I didn't find any problem , I test the other components out of the circuit (to be sure) , and they are okay, the sensor thermistor I don't know how to test.. I will check all of the camble , the pump, and hope to finding some strange things..Thank you...
Leave a comment:
-
Hi thank you for the answer, yes I replaced the large relay and some capacitor (not so good) the board have good voltage, It start normaly but somehow it stops in few seconds . Uln2003 I don't know how to test it... Tomorrow I will check cable etc. Thanks again...
Leave a comment:
-
Guys I'm here again , so nobody tells me what you think about it? Every reply is helpful...The machine still show me led red (ice full). But there's not ice or water in the bottom...I check everything no short... Those ir led sems works.. I almost mad with this thing..Dammed ! Thanks again...
Leave a comment:
-
You can find the chip already reprogrammed. Anyway , ae you sure that power supply is good..? Turn the tv on without the main board (tuner) only with power supply, if the led of pannel comes up and staying on then you have the answer is the main board faulty... like I said you can find the chip already programmed find some research on Google......
Leave a comment:
-
Hi guys this morning i had some spare time so I'm focused to cleaned those chip to find out the marked on it they are very clear and I hope someone help me with the schematic. I don't know where find it. Thanks to all the community...3 Photos
Leave a comment:
-
Machine to make ice doesn't work
I guys a friend of mine gives to me this thing, he said it's a machine to create ice. However it going on protection mode with led red (ice full) of course there's no ice, then I take the board control out and look it on the microscope, there are I rele blown up (A1) , (U5 it's like pwm) and other side of pcb there are two chip it looks not so good. My question is existing schematic for this pcb? Because if it's to expensive to repair of course is could be better to putting on the bin.. Thank you all for the answer 🙏...4 Photos
-
Hi guys I changed those components and it worked again.. thanks all for your help 🙏...
Leave a comment:
-
Hi thanks for your reply, yeah i already checked all four diode and they are good.... It seems that capacitor shorted and blown up the inductor and the chip......
Leave a comment:
-
To replace those resistor is a bit problem because the value is not very clear for me, I'm not a master, I'm trying but the calculator of resistor can't find all the colors of that. About the chip I don't think it's going to be a problem i can see clearly the mark on it...Thank you again...
Leave a comment:
-
Hi, thanks but ione of the resistor broken (I'll send you the picture,the other one (L100 is open <shorted> paint yellow)...2 Photos
Leave a comment:
-
Thanks, but as you can see, the resistor is broken. The PWM chip seems good, no blown up, and there is no dirty on it. Anyway I hope someone will place here the schematic diagram it will be useful.....
Leave a comment:
-
Beko microwave oven dead !
Hi guys, how's it going?I hope you're all doing well. So a friend of mine told me that his little oven just dead, no noise like spark or something no blown up, anything just dead. I opened it and on the board control I found capacitor dead (you can see the dirty on the pcb , resistor broken and the rest of capacitor are low value. I
just wanted to understand if existing the scheme for this controller board. Thank you do much for the answer5 Photos
No activity results to display
Show More
Leave a comment: