Hi everyone
I replaced the mainb of my Asus k501ux with a new one and in the bios under serial number there is clearly no serial number listed ... how do I enter the serial number of my machine in the bios
... I know that there are software for HP models that allow you to migrate the machine's data by inserting them into the bios
...can someone please give me an input if there are programs also for the Megatrends bios that allow you to write the machine's construction data into the bios?
Thank you​
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
-
Re: Acer A315-22 no power on
Hi....I removed Pr119 from mainb, in diode mode I measured at pin 1=2.4637
pin2= no measurement detected,...
with the photo sent I re-measured pq103 and pq105 and they respect the indications you have shown me
only measure detectable black tip on "D" and the red one on "S" 0.55 ohm
Thank you...Last edited by pippo_one; 08-22-2023, 12:13 PM.
Leave a comment:
-
Re: Acer A315-22 no power on
1.....pin1-2 = 0.0029
2....I can't confirm they are wrong .seee point 1
3.....CMSRC ACDRV = 359 Kohm
4.....0,5556 ohm
the pcb tracks are all intact from the pu101 up to the pq103-105
measurements performed with pr107 and pq107 unsoldered from the pcb...Last edited by pippo_one; 08-21-2023, 11:35 AM.
Leave a comment:
-
Re: Acer A315-22 no power on
Hi, over the weekend I took the liberty of measuring all the voltages of the Pu101 as suggested by @Prustel.. hoping that the values I post can be of help in understanding a possible solution.
I state that the measurements are performed with "pr107 and Pq107" unsoldered from the mainb and without battery (obviously discharged):
pin1=1,3mV
pin2=1,3mV
pin3=20nV
pin4=22mV
pin5=11mV
pin6=2,75V
pin7=2mV
pin8=8mV
pin9=80mV
pin10=0V
pin11=10mV...Last edited by pippo_one; 08-20-2023, 01:12 PM.
Leave a comment:
-
Re: Acer A315-22 no power on
resistance between pin1 and 2 = 0.02 ohm
red wire Pin1 ->black on gnd = open.
black wire Pin1-> red wire gnd = 330ohm
red wire pin2 -> black wire gnd = open
black wire pin2 -> red wire gng =305 ohm
Leave a comment:
-
Re: Acer A315-22 no power on
pin 28 ...19.65volt
pin 3 .... 4 m volt (millivolts)
pin24 ....6.05volt
pin5 .. 13mvolt (millivolts)
p.s.: pr107 e pq107 unsoldered...battery disconnectedLast edited by pippo_one; 08-18-2023, 03:20 AM.
Leave a comment:
-
Re: Acer A315-22 no power on
i unsoldered pq107 ...and i measured "ACDET" now i have 2.75volt
but in pin4 (ACDRV) of PU101 I still have 0 volts.
1-is it possible to argue that the PQ107 does not work properly?
2-if I reweld the PR107 can I make other measurements?
3- do you recommend replacing PQ107?Last edited by pippo_one; 08-18-2023, 01:01 AM.
Leave a comment:
-
-
Re: Acer A315-22 no power on
the measurements with the components still soldered on the board are:
Pr108= 260k
pr118= 53k
I measured the continuity between pr108 and pin6 of the pu101 and it's ok.
also at pin 1 of the pq107 I have 6.60 volts and at pin 3 of the pq107 I have 0 volts
Leave a comment:
-
Re: Acer A315-22 no power on
I update the post with the diagram of my mainboard, in summary I checked the Pq103 and Pq105 as described above by measuring about 315 ohms towards ground com
I unsoldered the Pr107 but from pin 4 of the Pu101 I don't see the approximately 25 volts suggested by @mon2
while in Vcc input of Pu101 I detect the 19,..( pin 28)
I'm also checking the "ACDET" line which according to the diagram should find 2.4 volts but I don't measure them, the line is 0 volts.
Can someone please give me some more input? Thank you
...Last edited by SMDFlea; 08-17-2023, 04:25 AM.
Leave a comment:
-
Re: Acer A315-22 no power on
Hi, I unsoldered pr107 placed at the output of pin 4 of the PU101 .... I applied voltage to the 19 v input, I measured the voltage of pin 4 (ACDRV) and no voltage is detected by the tester
any other suggestions?
Leave a comment:
-
Re: Acer A315-22 no power on
Sorry I got it all wrong delete the post above, tomorrow I will repeat the measures with the correct actions you gave me
Leave a comment:
-
Re: Acer A315-22 no power on
Hi @lun2 ...I carried out the measures you suggested in the following ways:
- with the resistance still soldered on the board, the red lead of the tester to the Gnd of the board and the black lead on the Drain of the Pq105 I measure 315ohm if I reverse the leads of the tester (red to Drain Pq105 and black to GND)
I don't measure any resistance
--I unsoldered the resistance and performed the measurements in the same way: the resistance is now 470ohm
and the other no measure
at this point, as suggested, I gave power to the...
Leave a comment:
-
Re: Acer A315-22 no power on
Hi @techtiger .. I'm a beginner and through you I try to learn as many things as possible and sorry for my non-technical language .... what does "CLR " mean?
please use more basic language with me ...thanks.
Another test performed: the input power supply of the "PU101" is 19 volts...but I can't measure with the "ACDRV" output tester (GATE 4)...Although it can be measured with the tester or it takes an oscilloscope?
I performed this test before your instructions arrived
any help is appreciated
Leave a comment:
-
Acer A315-22 no power on
Hi all .. I'm asking for help with a problem with an Acer A315-22
connected to its power supply with the tester I detect the voltage up to the DRAIN of the PQ103 ... then nothing more
I ran these tests
with the mosfet still welded I activated the GATE of the PQ103 and PQ105 I detect continuity with the tester from the Drain of 103 to the Drain of 105 ... but after 10/15 sec the continuity is interrupted
I can't figure out what it could be... can someone please help me
Thank you...
-
-
Re: la-9532p keyb
if you resflash the bios with the same version is it possible to repair the ec? (if it is corrupted)
Leave a comment:
-
-
No activity results to display
Show More
Leave a comment: