Hi everyone !
I am looking for firmware update for Toshiba 32LF221U19
stuck on fire tv display
main board is TD.T950.61 sticker ST3151A05-8
Thanks
d2fx
Member
Last Activity: 01-05-2026, 09:25 AM
Joined: 05-22-2015
Location: sxm
-
Hello,
here it is...Leave a comment:
-
LG OLED65C25LB power on/off status
Hello,
I don't have the same power on/off status as indicated in the service manual.
Would you have any other information about these codes? -
-
Thank you lotas
Leave a comment:
-
Samsung UE65RU7025K
Hello Everyone,
Samsung UE65RU7025K
TV turns on but no image.backlight ok.
I connected the fb-trdy-1 and fb-trdy-3 points, then applied the tape technique to the left end. Perfect image.
if I remove the jump, I have no more image
Is there a risk of leaving the points fb-trdy-1 and fb-trdy-3 permanently connected?​ -
It impresses me this high level
thank you for the explanation Lotas​Leave a comment:
-
Lotas,
I have a question (if it's not indiscreet).
how you made to fix the corrupt dump.
I do not see any similarity between the defective and the corrected.
Did you use a correction program or do you correct directly in As Programmer?
Thank you very much for sharing your knowledge on this forum.
you are a master​...Leave a comment:
-
Re: Samsung LN46B530P7N
hi
check ceramic caps on screen lvds pcb for shortsLeave a comment:
-
Re: Eeprom dump thread!
ledtv3226 coby...Last edited by d2fx; 07-11-2018, 08:23 AM.Leave a comment:
-
Re: Eeprom dump thread!
here it is for Samsung and lg panelLeave a comment:
-
Re: Eeprom dump thread!
Hello,
I need the dump for coby ledtv3226 please.
panel Samsung LTA320AN01
best regardsLast edited by d2fx; 07-10-2018, 02:48 PM.Leave a comment:
-
Re: Samsung UN40B6000vf /xza clicking noises
Hello Nosaj
The problem seems to be on the motherboard is to replace completely or to confided your board to a technician
the repair of the board requires equipment....
regardsLeave a comment:
-
Re: Samsung UN40B6000vf /xza clicking noises
hello
use the troubleshooting diagnostic no power I've sent
proper dc standby ok===>proper 12v;13v;5v ok====>3.3v at pin 5 of ic202 ???
no :ic202 hs
yes :go ahead 3.3vpin1 ic208......Leave a comment:
-
-
Re: Samsung UN40B6000vf /xza clicking noises
Not on to have the right to share this information if an administrator can answer me...Leave a comment:
-
Re: Samsung UN40B6000vf /xza clicking noises
maybe help...Leave a comment:
-
Re: Samsung UN40B6000vf /xza clicking noises
ok it s ic210 a regulator and not ic201Leave a comment:
-
Re: Samsung UN40B6000vf /xza clicking noises
Hello
no start up,relay click continuously
if your appliances using the "BN94-02657M" main board.
check Pin1 (3.3V) of IC210 inS/C to ground.
IC201 remove, but the line remains in S/C. Replace IC1501 (WM8593SEFT) on main board .Leave a comment:
-
Re: Panasonic TH50PX60U Power Problem
hello
do you have 5 volts stand by?
if yes check the s and k boards (power switch-power led)
many time I've see oxidation cut wireLeave a comment:
No activity results to display
Leave a comment: