AP-P348AM schematics?

mon2

Badcaps Legend

Join Date: Dec 2019

Posts: 14631

Country: Canada
#1

AP-P348AM schematics?

11-20-2024, 06:08 PM

Hi. Servicing a XBR75X850F with no power. Originally had no standby voltage of 3v3 -> found a defective SB260 diode (apparently a common fault) and now have this rail. No relay sound upon power up. Bypassed the POWER ON and T-Con with the standby voltage and do see the ~12v steady on the pin 26 of the power connector (T-CON). This implies bad emmc (Nick's TV repair YT videos). Replaced the BGA but still no power on LED / no relay.

Any suggestions on faults? Any schematics for this unit?

Did observe that the zener near the offline IC that feeds into opto-coupler is marked with '13B' yet the voltage is 3v3. The one marked (below this zener) @ '16B' is around 15-16v. The optos are PC123 (older units) and they appear to be ok when tested out of circuit.

No USB light flicker upon power up yet there is 5v present on the main controller board.

PS: The pics below were taken after removing the optos off the board. No blown fuses.
Tags: None

Previous template Next

On M-Audio AV40 active studio speaker's two zener diodes get really hot.

by Dvsr

Hi. I need help from wiser guys. I am amateur in electronics and can't figure this out by myself.
I bought faulty speakers, M-Audio AV40's. Other speaker has all the electronics in it and the other speaker is just passive one powered by the other speaker's amp. Original problem with the speakers was loud buzzing. I figured out that there is something wrong with the capacitors. I went ahead and replaced every electrolytic capacitor on the PCB. The caps are good quality and have the same values as the original ones.
After replacing the caps I started testing out the speaker. It seemed...

4 Photos
- Channel: Troubleshooting Audio Equipment
09-10-2025, 10:20 AM
What Zener Diodes on a Linear Power Supply

by caspian

Dear members,

I have a linear variable power supply with unknown brand name that I used for voltage injection.
Then it failed. I discovered that its transistors (Q1 and Q2) are shorted.
In addition, I discovered that its zener diodes are defective.
I can replace the burned transistors.
But I do not know the model of the zener diodes. the model number is not marked on the zener diodes.
Therefore, I cannot replace the zener diodes.
I do not want to test the zener diodes in a test circuit to discover their model or value.
no schematics are available...
- Channel: Troubleshooting Power Supplies and Power Supply Design
05-26-2025, 12:38 PM
Garage door RX unit (Cardin S38C) does not short relay to send opening signal

by CoinCoin88

Hello everyone,

I'm turning to the Badcaps community to help me troubleshoot the radio Rx card from my (old) garage door opener. While I could just ditch that card and replace the whole system, I first would like to understand "why" it suddenly stopped working, because that's just how I am wired...!

Some basics: the receiver works on a 30.875 Mhz frequency. Yes, I'm aware this is not in use anymore in a looot of places. It does not use any rolling code, it's just a regular dip-switch code that you have to set up on both the receiver and transmitter. The receiver...
- Channel: General Electronics Technical Discussion
09-15-2025, 03:36 AM
9V relay temperature 40C

by jm1234

Hi, I'm seeing one 9V relay having temperature 40C on its 9V (primary) side. Does that seem right? I switched 2 relays on that board and the temperature was the same (on the same position), so I'm sure it's not a faulty relay. I measured voltage on that relay and it was 9.5V DC, so that looks good. I don't see any other relay on that board having that kind of temperature and they have 9V on them too.
I thought maybe the transistor that is switching this relay keeps switching on/off, so I also checked for AC and there was almost none: 0.3V using mV range. No steady frequency was shown, but...
- Channel: Troubleshooting Appliances and other Household Electronic Stuff
05-09-2024, 03:03 AM
Biomass Boiler not driving cleaner motor relay. ENERTRES BIOMASA BI-650

by edugimeno

Hi everyone!
I have this board that suddenly stopped supplying power to an output that drives an interchanger cleaner motor.
I checked while the board was in place with all wires attached and there's no AC voltage on the corresponding plug X5
This X5 is driven by fuse F8 (tested OK) which comes from the second orange relay
To make sure there are no charcoaled contacts inside the relay, I got a 24VDC power supply and got it ready to manually power up the coil side of these relays.
I respected the polarity, positive to cathode of protecting diode
So provided all...
- Channel: General Electronics Technical Discussion
04-18-2024, 01:15 PM
Loading...
No more items.

AP-P348AM schematics?

AP-P348AM schematics?

Related Topics