iMac A1311 PSU 614-0444

mccltd

Member

Join Date: Sep 2017

Posts: 10

Country: UK
#1

iMac A1311 PSU 614-0444

11-27-2017, 07:44 AM

I have an A1311 that has blown the fuse but checking to line to ground it has continuity.
Does anybody have a schematic for the PSU unit? 614-0444

Just testing D104 and it has continuity both ways so that's one faulty component.

Last edited by mccltd; 11-27-2017, 07:53 AM.
Tags: None

Previous template Next

iMac A1311 - Motherboard 820-3126-A, turn on sometimes

by ryogadan78

Hi guys, I have this 2011 iMac A1311 with a strange problem.

Most of the time, when I plug in the power cord, the first of the 4 LED's turn on, but when I press the power switch the LED turns off and iMac won't boot up.
Sometimes, when I unplug and plug the power cord back in, iMac starts up correctly by turning on the 4 LEDs in sequence.

I have already tried a new power supply, but the result does not change. Do you have any suggestions?

Motherboard 820-3126-A
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
04-06-2024, 05:19 AM
iMac A1311 EMC 2389 mid2010

by Melania Ulibarrie

Hi, Need boardview and schematic of iMac A1311 EMC 2389 Mid2010
- Channel: Schematic Requests ONLY!
04-16-2025, 09:03 AM
trying to repair imac motherboard model A1311 (late 2009)

by jasobrino

Hello everyone,
Some time ago I acquired an imac computer model A1311 that does not boot (motherboard ref. 820-2494-A).
The power supply is working properly (I have two), it delivers the 12V on pin 4 of the power connector (PP12V_S5).
As I have the schematic diagram and the boardview, I have made a series of measurements, obtaining the following results:

PP12V_S5 -> 12V
3V3REG_VCC -> 3.12V (something low?)
PP5V_S5_LDO -> 0.02V
3V3REG_VCC -> 0.0066V

I have also measured the resistance to ground on the coils, and I can't find...
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
02-20-2024, 11:48 AM
IMAC A1311 820-2784 BOARD NO DISPLAY

by NConstantinou

DEAR ALL
i have the above board,, when i power on led604 does not come on. i do have PP3V3_S0, which goes across resistor R604.here i have again 3.3v,then does to led604. The lead of the LED that is connected to Q602 D-S i get 1.9v is that correct!
on Gate which is MXM_GOOD i get 0v which is connected to PCH ic.
is my problem the PCH IC!

Thanks
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
03-22-2025, 02:18 AM
iMac A1311 PSU repair questions

by Crystaleyes

Hi all.

I have an ongoing issue with a 2010 A1311 21.5" iMac. It starts up, chimes, lights up and boots to the OS, however the screen starts to lightly flicker, steadily getting worse before switching off altogether. Measuring the voltages reveals that the 12v rail drops to around 10.5v once the Mac is switched on.

Until yesterday, I wasn't sure if the problem lay with the PSU, the backlight inverter or the logic board.
Yesterday, however, I borrowed a good PSU and the iMac works fine.

Hence my opening a new thread within this troublshooting...
- Channel: Troubleshooting Power Supplies and Power Supply Design
07-04-2022, 04:50 PM
Loading...
No more items.

iMac A1311 PSU 614-0444

iMac A1311 PSU 614-0444

Related Topics