JTC B-28 Cardmp3 player amplifier Schematic

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Billcliffens
    New Member
    • Nov 2023
    • 1
    • Kenya
    #1

    JTC B-28 Cardmp3 player amplifier Schematic

    I'm trying to troubleshoot a JTC B-28 Cardmp3player amplifier which had a power supply failure. I've replaced the damaged str transistor with a 3wire power module and now it's powering up fine but it has very low and poor quality audio output.
    A schematic of this 12vDC/220vAC Power amplifier will be of great help.
    Last edited by SMDFlea; 11-26-2023, 04:38 AM.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • KeyResults
      Roland SPA-120 Amplifier Tech Notes / SM / Schematic Source?
      by KeyResults
      Repairing a Roland SPA-120 amplifier, a solid-state early-mid 80's part of the Roland Rack. The PCB is Labled AP-124B. Was thinking lytics would resolve the nasty output on scope but all tested 100% for values, ESR, and leakage (very surprised!). Symptom is nasty wave form on both channels in Stereo mode, but clean in single channel mono (BTL) mode. The Output transistors test ok at room temp, but still could be faulty once heated up. Anyway, a schematic and some test point voltages would sure save some time. Thx!
      4 Photos
      11-09-2024, 03:21 PM
    • nervous_capybara
      Repairing the Hitachi DA-6000 CD player
      by nervous_capybara
      Hello everyone !

      I recently conducted maintenance on a Hitachi DA-6000 CD player for my grandparents : it had two distinct issues.
      Feel free to share your experience if you ran into other issues.

      DISCLAIMER : BE VERY CAREFULL WHEN OPERATING ON THIS SYSTEM : THE HIGH VOLTAGE IS VERY CLOSE TO THE VARIOUS TESTING POINTS, PROCEED WITH CAUTION

      CD tray would not come out of the player
      I could hear a motor spinning inside the player but the CD tray would not come out.
      Turned out that the issue was the CD tray belt that aged poorly and began to...
      11-05-2025, 03:11 AM
    • TinkerTron
      Schematic vs. Reality: Where Are the Resistors on My Sharp Clock Radio? Model FY-70CH
      by TinkerTron
      Hey everyone,

      I'm currently working on a mid-70s Sharp Electronic Digital Clock Radio, Model FY-70CH. I found the service manual online, printed it out, and have been studying it for a while. My main reasons for tackling this are: (1) I want to learn electronics and figured I'd start with something I had on hand, and (2) I want to fix its issues. Right now, the radio sounds awful, has about 5V DC at the speaker terminals, and the alarm time setting doesn't work. But I'm not asking how to fix these problems.

      Instead, here's what's been bugging me so far:
      The schematic...
      3 Photos
      03-06-2025, 02:03 PM
    • atunguyd
      Acer x163w Monitor PSU schematic
      by atunguyd
      Ii wonder if anyone can help me. I have a Acer x163w monitor which is not powering up. The PSU main capacitor's one leg had completly come off - I replaced it but the PSU is still not outputting DC. I found the monitor in questions service manual here on manuals lib but the schematic in there is a completely different - the schematic shows no mosfet to drive the transformer while the one I have does use a mosfet - also the schematic shows only one optocoupler but mine has two.
      The PSU board is labelled FM-20A02-AAA made by APD as per the image below. I am trying to find a schematic for this...
      03-05-2025, 02:08 PM
    • Sdhjm
      Schematic with element ratings hp victus 15 dag3pmb18b0 rev:b g3p
      by Sdhjm
      I'm asking if anyone has a schematic for the dag3pmb18b0 rev:b g3p board. I found a schematic of the board, but I don't have the component numbers. If anyone needs a schematic, I can send it to you, but I don't have the numbers....
      11-26-2025, 03:43 AM
    • Loading...
    • No more items.
    Working...