TO-66 and TO-3 packages

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • japlytic
    Badcaps Legend
    • Oct 2005
    • 2086
    • Australia

    #1

    TO-66 and TO-3 packages

    For at least 25 years (if that is correct), no new devices (not NTE/ECG) in the TO-66 package have been introduced - the closest equivalent to the TO-66 package is the popular TO-220 package in terms of dissipation.
    I am not sure about this, but new devices in the TO-3 package have not been introduced for at least 10 years - the closest equivalent to the TO-3 package is the TO-264 or TO-3P (not the TOP-3) in terms of dissipation (the TO-3 package MJ11032 can dissipate up to 300W and the TO-264 MJL21193 can dissipate up to 200W).
    My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.

Related Topics

Collapse

  • Document Archive
    Mounting and Handling Guidelines for TO220 TO220F TO247 Cases / Packages
    by Document Archive
    Mounting and Handling Guidelines for TO220 TO220F TO247 Cases / Packages

    The TO220, TO220F and TO247 are the popular packages for power devices because of their versatility and ability to dissipate moderate amounts of heat. This application note describes the basic guidelines for handling power MOSFETs in TO220, TO220 and TO247 packages shown in Figure 1. Please note that only mechanical and soldering guidelines are covered here. Additional precautions are required for isolating high voltage rated devices to meet safety regulations.

    Securing a good thermal interface between...
    10-07-2024, 04:35 AM
  • Dan the Dog
    SMD Diode S3 marked on package
    by Dan the Dog
    I need to find a replacement for this diode on one of the six gate drivers of a full-bridge IGBT inverter for a servo motor. It has S3 on the package. How can I find out for sure the right diode that I need. I believe it is schottky because it has 0.2V drop across.

    The anode is on pin Ve and cathode on pin DESAT on 316J gate driver IC. Also would be nice if anyone had an idea of the purpose it is serving as it is not included in the suggested schematic of the 316J datasheet.


    I have also drawn a partial schematic of the gate driver in this servo amplifier to try...
    05-26-2024, 09:45 AM
  • Document Archive
    DELL Inspiron 3670 Inspiron 3000 i7-8700 Specification for Upgrade or Repair
    by Document Archive
    This specification for the DELL Inspiron 3670 can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the Inspiron 3670 boardview and Inspiron 3670 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download for DELL...
    09-12-2024, 02:15 PM
  • Srdjan01
    Oral-B IO Series 6
    by Srdjan01
    Hi everybody.
    I'm trying to fix this toothbrush that doesn't wanna start. And I need your help.

    Just to inform you that I'm supperbeginner

    First photos are from internet because I did not took a photo of whole board.

    I have noticed that fuse marked with "E" near the battery pole is bad and decided to short it with a "proper calibrated wire" as one would say.
    Now, when I apply 1V from the power supply, limited to 500mA, one of the component stick out from the rosin mist. CHC N2AB (or some variation of that letters) is the hottest...
    03-05-2025, 10:05 AM
  • summerwhite
    MSI GF63 IACEN component identify
    by summerwhite
    Hi peeps,

    Customer brought in a MSI laptop where when dropped the battery has knocked some components off the board. Coil, capacitor and this IACEN package that I cant find online.

    The packages legs where bent to hell and when i tried to pull them back they broke off the package. (also ripped trace but thats easy to fix)

    This is the orginal one


    This is another one I found on the board.


    Can anyone help me find this component online to buy? I also double checked the doner boards I have and cant find this package...
    10-24-2023, 07:38 PM
  • Loading...
  • No more items.
Working...