UpDate ZD-915 Desoldering Station Repair

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • sam_sam_sam
    Badcaps Legend
    • Jul 2011
    • 6039
    • USA
    #1

    UpDate ZD-915 Desoldering Station Repair

    If you have one of these De-soldering Station there is an important repair

    IF

    You have this problem

    When you try to power up it -----> and it stays on for 2 seconds and goes OFF and restarts and keep doing same thing here is the fix for this problem

    or if you can hold the suction switch and turn unit on and powers off and on
    replace diode D1 = M7

    The problem was ( D1 ) shorted the part # is ( M7 )


    If you want to have blow up view of the photos go to this post
    https://www.badcaps.net/forum/showthread.php?t=39651
    Go to post # 20

    Here is were you find this diode

    http://www.ebay.com/itm/100Pcs-1N400...UAAOSw~gRV5mGP

    I hope this help
    Attached Files
    Last edited by sam_sam_sam; 12-23-2015, 06:49 PM.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • sam_sam_sam
      Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
      by sam_sam_sam
      I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

      One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
      03-31-2024, 02:12 PM
    • armini
      18VDC PSU completely dead - ZD-915 desoldering station
      by armini
      Hi everyone!

      Three years ago I got a ZD-915 desoldering station which failed just after a few months of light use. During a short desoldering session, the station simply shut down, and since then it has been completely dead and unresponsive. The failure was silent, without any pops.

      Due to a lack of time, I set it aside and didn't look at it.

      Yesterday, I took it apart and did some basic measurements. The 18v terminal shows 0v. In addition, there is no visible damage to the board itself.

      According to replies in 18VDC PSU has dropped to...
      04-25-2023, 07:49 AM
    • sam_sam_sam
      Modification to a ZD-987 desoldering/soldering station using a external switching power supply
      by sam_sam_sam
      I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

      I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
      07-01-2024, 06:34 AM
    • Document Archive
      HP Station de travail Z2 format tour G4 i7-8700 Specification for Upgrade or Repair
      by Document Archive
      This specification for the HP Station de travail Z2 format tour G4 can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the Station de travail Z2 format tour G4 boardview and Station de travail Z2 format tour G4 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no...
      09-12-2024, 02:20 PM
    • Document Archive
      MSI Gaming GF66 11UG-820FR Katana Dragon Station Notebook GF Specification for Upgrade or Repair
      by Document Archive
      This specification for the MSI Gaming GF66 11UG-820FR Katana Dragon Station Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the GF66 11UG-820FR Katana Dragon Station boardview and GF66 11UG-820FR Katana Dragon Station schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note...
      09-07-2024, 05:20 AM
    • Loading...
    • No more items.
    Working...