There's now a very large torrent archive of many devices including iPads/iPhones/etc if you go to the end of this thread.
[url]https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/3517508-important-information-xinzhizao-xzz-pcb-file-format-is-now-supported-by-flexbv-free-and-licenced-editions[/url]https://There's now a very large tor...-hardware-devi
inflex
Badcaps Veteran
Last Activity: Yesterday, 08:19 PM
Joined: 08-10-2012
Location: Townsville, QLD
-
Correct, yes UP800. Normally I'm not one to subscribe to the notion of pulling chips without first determining a viable cause to blame them but sometimes after all this sort of work you end up just throwing caution in to the air and trying. At least it's a comparatively simple chip. Other possibility of course is the display connector itself....Leave a comment:
-
I just realised, YES, you already have removed those parts
Try remove the controller, just for the hell of it too....Leave a comment:
-
Right, sorry about that one - I misinterpreted your pictures where you had the LCD connector + removed caps next to them in the next picture, definitely my bad there.
Did you also remove RP831 ? It's a resistor that takes the voltage back across XWP801 (internal link) to the controller. If you remove that and the short remains, then I'd say you've got a bad board likely. If the short disappears then look at the FB line parts and the controller
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid"...Leave a comment:
-
There's more caps off to the side of the screen connector and near the main storage caps that you've already removed.
Do you have the boardview & schematic and a boardviewing program? This is FlexBV5 ( [url]https://pldaniels.com/flexbv5[/url] ) which has a free edition which may help you out here.
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3543127}[/ATTACH]
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid&qu...Leave a comment:
-
Yes, I spent quite a bit of time here in Badcaps, have been here for many years now ( Just don't post a lot ).
Starting to worry that your board might have an internal short at the rate it's going; based on that cooked off inductor in the original posts it might have happened, hopefully not. Looks like Mon2 is guiding you though. Best of luck....Leave a comment:
-
Just weighing in here, I've had a lot of these units, and yes, keep removing those caps one by one; eventually you'll probably find one with a crack on the underside. They can be sneaky!Leave a comment:
-
Apologies for asking for help
NM-B911 board, PLT_RST# present but no activity other than a backlight activation and 5V on USB/HDMI.
Tried a few other sample BIOS bin's here but none did anything ( in fact even worse ).
Original BIN attached here.
Type: 20NB-001TUS
SN: PF1LTR13 ( I think this is it, I had to reconstruct the barcode as the ASCII version was rubbed out and the barcode smeared )...Leave a comment:
-
Send the boardview file to me and what version are you using? Free, demo or licenced?...Leave a comment:
-
[URL="https://pldaniels.com/flexbv5?fbclid=IwZXh0bgNhZW0CMTAAAR3A0EUwavtTk48QsM1oo3TKO_FCh2S87iFmKQ6NE2wzckLHUkErDut6ZQs_aem_-AeyyugWVZ-JD63BD2PuFQ"]https://pldaniels.com/flexbv5[/URL]
FlexBV 5.0474 is now out.
This is a refinement from the recent XZZ-pcb enabled version with improved holes/pads handling
Free Windows and macOS versions are also signed now too in addition to the rest.​
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3533368}[/ATTACH][URL="https://pldaniels.com/flexbv5?fbclid=IwZXh0bgNhZW0CMTAAAR3A0EUwavtTk48QsM1oo3TKO_FCh2S87iFmKQ6NE2wzckLHUkErDut6ZQs_aem_-AeyyugWVZ-JD63BD2PuFQ"]https://pldaniels.com/flexbv5[/URL]...Leave a comment:
-
I'm not involved in extracting the files; that's the task of other people, my purpose was to decode the format. I'm sure more and more the files will become available for everyone to access. I suspect it will be announced here in Badcaps.
Did you see this in the search? [url]https://www.badcaps.net/forum/document-software-archive/schematics-and-boardviews/3524642-drone-game-console-boardview-files-from-xzz[/url]https://I'm not involved in extracti...come available...Leave a comment:
-
https://[url]http://194.195.124.128/...onsoles so far[url]http://194.195.124.128/files[/url]
user & pass rtr
Has iPhones, iPads (from here) and some Gaming consoles so farLeave a comment:
-
No plans to; already have my hands full with trying to grind through file formats and usual updates....Leave a comment:
-
Wow, that's so much for the comment. The data has been out for a while but a lot of people don't have it - thanks for contributing, we're so thankful....Leave a comment:
-
Good to know....Leave a comment:
-
I've been advised there's a new preferred torrent magnet link if you'd be able to utilise this instead ( supposedly to help the balancing )
magnet:?xt=urn:btih:5e9077dcb107fb23899c7f6ac7c8adbc9b8f38f6&dn=XZZ&tr=udp%3A%2F%2Ftracker.opentrackr.org%3A1337%2Fannounce&tr=udp%3A%2F%2Fopen.tracker.cl%3A1337%2Fannounce&tr=udp%3A%2F%2Fopen.stealth.si%3A80%2Fannounce...Leave a comment:
-
I've not seen many of the files (pcb) converted to GenCAD (cad) other than one or two that we've had to literally cash favours in just to get our hands on. If someone was able to convert them in the past then it's very annoying that they hadn't been sharing with the rest of the community. At least now we can ALL download pcb files out of XZZ and read them directly without needing to wait for someone to be "kind enough" to convert them
I know I've got the iP13~16 files now which aren't in this large download archive. Early days yet, someone will likely set up a...Leave a comment:
-
It's just a starter for people who haven't already gotten their hands on it before. There's plenty of new ones that can subsequently be downloaded individually....Leave a comment:
-
If people are after an archive of files, please try this magnet link and also, once it has all downloaded ( ~65GB ) please consider leaving the client running for a bit to help the data "get out there".
magnet:?xt=urn:btih:5e9077dcb107fb23899c7f6ac7c8adbc9b8f38f6&dn=XZZLeave a comment:
-
Not yet but I know there's a few people working on it. One I have is about 70GB compressed up but is now a bit out of date ( and I don't have a way of hosting it ).
Keep tabs on this thread and hoping in the next 24hrs we'll have something....Leave a comment:
No activity results to display
Leave a comment: