ProSis
Senior Member
Last Activity: 06-15-2026, 07:39 AM
Joined: 06-29-2017
Location: Bafra
-
Thank you, it worked without any issues and the password is removed. Good stuff, buddy!... -
reeder TU141I rev 1.0 A bios password.
The brand of the device is Reeder, but since the model number and serial number information are not located under the chassis, I cannot provide the exact model and serial details. The only information available is the motherboard code, which reads "TU141I rev 1.0a". A BIOS password has been set and forgotten on this device, and I would appreciate it if we could remove this password. Thank you in advance for your help... -
I got the display working without any issues, thank you. However, my device is still not charging. Could you tell me which pins should have how many volts for the charging to start?...Leave a comment:
-
ok...
Leave a comment:
-
QR Code...
Leave a comment:
-
I am experiencing an issue with my device not charging. Because of this, I would like to try updating or reflashing the BIOS. If this model has any known common issues related to this problem, I would appreciate your guidance.
I have attached the original BIOS file.
Chassis Code: UX434F
Motherboard Code: UX334FL Rev 2.0
Serial Number: L3N0Cv09192113E...Leave a comment:
-
I need to disable the onboard RAM for my device whose information is provided below. Could you please help me?
I only have a 16 MB BIOS available, I couldn't read the 8 MB one with the EEPROM device.
Lenovo V15 G3 IAP
SN: PF4TMGQH
Mainboad : NM-E361 Rev 1.0...Leave a comment:
-
It still shows “Manufacturing Mode Active” and I just can’t fix it.
The Service Tag and other details are visible in the BIOS as shown in the picture. I don’t understand why it’s behaving like this....Leave a comment:
-
I printed the file you gave me. When I enter the service tag in the BIOS and press save, it doesn’t save; it stays as shown in the attached image....
Leave a comment:
-
Hello,
I have a Dell Vostro 3500 laptop with no display. I found and flashed a working BIOS, but after flashing, the system shows “Manufacturing Mode Active”.
I believe this is caused by missing Service Tag / DMI information. I still have the original BIOS dump, however I was not able to extract the Service Tag and board-specific data from the original BIOS and transfer it into the working BIOS file.
If anyone can help with copying/injecting the Service Tag (DMI data) from the original BIOS to the working BIOS, I would really appreciate it.
Also, any...Leave a comment:
-
I kindly ask for your help regarding this file, as I really need it. Unfortunately, I’m unable to purchase a premium account because the payment system is not available in the country where I live. I would really appreciate any assistance or alternative you could offerLeave a comment:
-
Please re-upload. It gives an Invalid File Specified error during downloading....Leave a comment:
-
Thanks but it didn't show the image my friend...Leave a comment:
-
Thank you but it never opened with this file (it does not start)...Leave a comment:
-
Is there anyone who can help?Leave a comment:
-
I still need itLeave a comment:
-
Although I searched everywhere, I couldn't find the file I needed. I tried to do it myself and couldn't do it either. I would be very happy if you could help me.
Brand: Asus
Model: S432F
Serial: K7N0CX05K540292
Motherboard Model: X432FA REV 2.0
...Leave a comment:
-
1st leg resistance is around 0.5M (500K)Leave a comment:
-
Dc2 1. but not a short circuit.
When I remove the DC2 and draw a line from the 3rd leg to the 1st leg, 3V comes on without any problems and the computer works.Leave a comment:
-
LA-E991P +RTCVCC PROBLEM
I have an Inspiron 15 Gaming 7577 Model device. motherboard code LA-E991P Rev 1.0.
The problem with the motherboard is that when I connect the bios battery, its voltage drops from 3v to 0.8.
0.8v comes to the 2nd leg of DC2 and around 0.6v comes out from the 1st leg.
But when I remove the bios battery and connect the adapter, 3v comes from the 3rd leg and 3v comes from the 1st leg without any problems and the device works without any problems.
and when I connect the bios battery, the device does not start.
DC2 was replaced and the problem...Last edited by SMDFlea; 01-17-2024, 05:05 PM.
No activity results to display
Leave a comment: