Re: Pioneer VSX-324 suddenly the HDMI stops working
The problem is that it's not happening with the lid open so, if The lid is closed then it shutoff but if then I will open the lid, the receiver will work normally and thus I can't pinpoint the problem...
buchman
Badcaps Veteran
Last Activity: 06-10-2023, 06:12 AM
Joined: 08-06-2015
Location: burgas
-
Re: Pioneer VSX-324 suddenly the HDMI stops working
The HDMI problem is for all ports.
What do you mean by saying CLEAN the board? From dust?Leave a comment:
-
Re: Pioneer VSX-324 suddenly the HDMI stops working
I agree with you guys, definitely heat related, the question is how to discover the problem.
I don't have an infrared camera, it's very expensive.
Yes it's clean inside....Last edited by buchman; 04-24-2023, 11:33 PM.Leave a comment:
-
Re: Pioneer VSX-324 suddenly the HDMI stops working
I have noticed that when the lid is open, it doesn't happen.
Any clues?Leave a comment:
-
Pioneer VSX-324 suddenly the HDMI stops working
Hi all,
Recently, when I watch a movie, after a few minutes suddenly the red HDMI light on front of the receiver goes off and there is no picture and no sound but, the receiver itself stays on!
Then, when I turn it off for a few seconds and turn it back on, it keeps working for another few minutes and then the HDMI turns off once again.
Tried to do the factory reset and it didn't help.
What could be the problem? If it's one of the components inside then I can replace it if someone can pinpoint to the faulty component.
Thanks in advance.Last edited by buchman; 04-10-2023, 07:43 AM. -
Toshiba laptop dead pixles
Hi guys,
Tried a few fixes from YouTube to fix the dead pixels and nothing works.
Probably it's one of the components inside.
Which components can make such issue?
When I say components I mean a transistor, capacitor, resistor etc.
Thanks in advance.... -
Re: How to connect 6 monitors to a PC?
Bought this one, hope it will be OK.
I want more monitors for stock trading.
My power supply is Corsair TX750M.
[url]https://www.ebay.com/itm/Plugable-7-Port-USB-3-0-Hub-with-36W-Power-Adapter-/254032240352?_trksid=p2349624.m46890.l49292[/url]Re: How to connect 6 monitors to a P...-Adapter-/2540Leave a comment:
-
Re: How to connect 6 monitors to a PC?
I have 5 outputs but 4 are actual streaming. I think it depends on the version for each country....Leave a comment:
-
Re: How to connect 6 monitors to a PC?
Isn't there another option except adding a second graphics card? Maybe some kind of HUB or a splitter?
Some one told me that I have to install same graphics card that I currently have. In addition, I need to upgrade the power supply, do I? I have 750W right nowLeave a comment:
-
Re: How to connect 6 monitors to a PC?
I forgot to mention that I need to see a different picture on all monitors.
Do you have a link with an example of the video amplifier?
I googled it and it seems that it's not what I am looking for....Leave a comment:
-
How to connect 6 monitors to a PC?
Hi,
I built an AMD PC and I have GTX 1070ti graphics card with only 4 outputs to 4 monitors, I want to connect 2-3 more monitors, what are the cheapest options do I have?
Thanks in advance. -
Re: No backlight but LEDs are fine
I checked the voltage on the connector that is located on the power supply board with the LED plug on and off and the voltage on that connector that located on the power supply board is still fluctuate....Leave a comment:
-
Re: No backlight but LEDs are fine
Just checked with the LED plug off and the result is the same.Leave a comment:
-
Re: No backlight but LEDs are fine
Yes I removed the LCD screen. Seems like all leds light up the same brightness...Leave a comment:
-
Re: No backlight but LEDs are fine
I checked each LED strip with a power supply and they all work fineLeave a comment:
-
Re: No backlight but LEDs are fine
The voltage flactuate very fast between 70V to -100V.
What does that mean when the voltage goes to a negative zone?...Leave a comment:
-
Re: No backlight but LEDs are fine
Thanks for your reply guys.
Well, when the red probe is on the ANODE pin then the voltage jump to 150V and after a second to 200V and then fluctuate between 180-200V.
When the red probe is on CATHODE pin then the voltage rises to around 80V and then fluctuate between 60-80V.
I bought this TV for about 15 dollars and the guy said that there is a sound but no picture. I once fixed a TV like that by replacing a few LEDs and I thought that this time would be the same but when I opened and checked the LEDs, they were...Leave a comment:
-
Toshiba 40L2400VQ No backlight but LEDs are fine
Hi,
I have a Toshiba LED tv model number 40L2400VQ.
I don't receive the correct voltage at the output to the LEDs.
I disassembled the front panel and checked all leds and they are fine. Then I checked the voltage to the leds on the power board and it flactuate in milivolts.
Tested all caps with esr meter and they are fine.
The diodes are fine and the resistors too.
Where should I concentrate on?
Thanks in advance.... -
Re: How is called that compound that glues components on the PCB?
No, I don't need a thermal adhesive, I need some kind of silicone to glue a capacitor that I have replaced.Leave a comment:
-
Re: How is called that compound that glues components on the PCB?
I attached a photo....Leave a comment:
No activity results to display
Leave a comment: