User Profile
Collapse
-
HP LA-H32AP motherboard power on for 5 secs
Hello.
Received a LA-H32AP motherboard with AMD cpu, only reaction is the power led (LED1) that lights up for 5 secs, nothing else.
Summary↓
The laptop was working normally the previous day.
When pressing the power button, LED1 (Power LED) turns on for a few seconds and then turns off. The motherboard does not boot.
Some power rails remain active for several seconds after LED1 turns off.
Troubleshooting already performed:- Tested different RAM modules.
- Tested without RAM.
- Tested again with RAM installed — exactly the same behavior.
- Removed
-
Drivelock on Kingston A400 SSD
Hello!
We bought a lot of SSD disks 2.5", one of them is locked on Dell machine, this particular SSD is driving me nuts and i'll explain why.
I put it on a 7040 SFF, pc starts and prompts to enter password in order to use the SSD (attachment below), i visit bios-pw.org, put the serial tag as on attachment and i get result 5ah3Zd2fdpK0njZl
Then i enter this result and with Alt+Enter i get "wrong password", i have tried over 20 times and i still get wrong password.
I even put the 5ah3Zd2fdpK0njZl on AI with copy paste and ask it to spell the letters one by... -
Well PR1 gives only ~350mV on both pins now.
On PQ1 i get pin 1 and pin 3 are on ~340mV and pin 2 is on 5v.
Previous measurement on PR5 was wrong, perhaps i made a mistake, now i get PR5 pin1 = 380mV and PR5 pin2 = 3.3 V.
Also a resume (took all measurements again):PR5 pin2 3.3 V PR5 pin1 / PS_ID 380 mV ...PR1 pin2 / PS_ID 380 mV Leave a comment:
-
Νο 3v on PS_ID (measured on PR1 pin 2 and PR5 pin1) i get only 0.7v. Tried different jacks, have 3 here also different chargers, no luck.
PD1 and PQ1 replaced from donor board, there's a small chance one of them to be faulty since not brand new. How can i check them?
PD1 gives 0.8Ω on pin1 and several ΜΩ on pin 2 and 3....Leave a comment:
-
Have a LA-F121P motherboard that won't charge.
Replaced PQ1 and PD1 from donor board (so there is a very small chance they are faulty too) and i measure voltages and resistances as below:
PR1: 033.5Ω
PR2: 0.08Ω
PR5: 2.2kΩ
PR1: Pin1 to ground 385mv
PR1: Pin2 to ground 340mv
PR2: Pin1 to ground 380v
PR2: Pin2 to ground 3.3v
PR5: Pin1 to ground 2.8v
PR5: Pin2 to ground 2.8v
Please help!
Thank you in advance!Leave a comment:
-
So it is indeed MEC and not ITE like 2 of 3 motherboard archives suggest in SVOD database.
I will try jtag.
Thank yoy max!...Leave a comment:
-
SVOD4 on NM-B891 ( Lenovo X390)
Hello!
I'm newbie to SVOD4 world and i'm trying to flash EC on a NM-B891 motherboard.
My problem is that SVOD4 software is not helping much, first on Mb online Database it shows 2x NM-B891, one with ITE and one with MEC, both don't name pinout just NC and i don't understand where to connect what and through which way?
Through KBC connector or JTAG on motherboard?
What i miss here?
Thank you in advance!1 Photo -
I did but seems like every MB has a different way, some even need resistor removing to get in program mode. Anyway thank you.Leave a comment:
-
-
Managed to write BIOS and EC, i was unsuccessful with EC, i feel super idiot that i can't figure out how to use SVOD4.
Anyway with this BIOS and EC the behavior is same like all other dumps i tried, only 3 led blinks on power button, nothing else....Leave a comment:
-
Have you noticed anything wrong? Is very important for this case....Leave a comment:
-
-
Actually any BIOS that i have used resulted in 3 led blinks, only it's original dump lights up with nothing on screen.
I flash only BIOS, nothing else.Leave a comment:
-
Received a X390 (not Yoga) that powers up but shows nothing on screen, i tried bios from post #15 but is not working at all (only 3 led blinks)
Can you please confirm if my bios is ok and if possible provide MEC programming file?
Thank you in advance!
S/N: PC-18Y28V
NM-B891 Rev:2.0
Type: 20Q0-S0MP00...Leave a comment:
No activity results to display
Show More
Leave a comment: