Ampli Luxman LV-100

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • ranimar
    New Member
    • Sep 2024
    • 2
    • it
    #1

    Ampli Luxman LV-100

    I have an LV-100 amplifier that as soon as I turn up the volume it greatly distorts the audio on both channels. I have already checked part of the electrolytic capacitors and replaced IC Hybrid-IC STK3042III without solving the problem.
    I know it is worth little but it is a memory and I would like to repair it. thanks to those who can help me.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • mikkele86
      Luxman R-5045 - Capacitor at amplifier output broke, can i replace with higher capacitance ?
      by mikkele86
      Hello Im renovation a Luxman R-5045

      On the attached picture there is a cap 0.047uF (47nF) and a resistor, 10ohm. What is their purpose ? and what would happend if I were to replace the caps with lets say, 10nF or 100nF ?
      because thats what i got in stock :/

      ​...
      1 Photo
      04-16-2024, 12:37 PM
    • waigy
      Nikkai EAPA 450 car amplifier rear speaker output is a low level and distorts easily
      by waigy
      As the title.
      I think these used to be sold in maplins a lot of years ago, it is an antique, but it's just fine for my needs.
      It looks basic enough inside with large components so I could do a full recap pretty easily.
      Any suggestions on what component would cause the symptoms of low volume output on both left and right rear speaker outputs?
      If I turn up the rear gain level in the amp until the speakers start to distort it starts to distort quickly even though the speakers are still pretty quiet.
      I thought I had dodgy speakers as I just fitted new old stock 6x9s in...
      17 Photos
      11-08-2024, 03:53 AM
    • klipschfan
      Luxman M-117 amplifier
      by klipschfan
      Hello everyone, I'm new to the electronics repair hobby. I could not afford a Luxman M-117 so I purchased a broken one and figured I would try my hand at repairing this one. So here goes.... The right channel has -74 volts DC at the speaker terminals all of the output transistors are showing the same -74 volt on the emitter leg. Should I remove all of the output transistors and test? I have attached a service manual. Any help would be appreciated?...
      08-31-2022, 01:35 PM
    • MrCommunistGen
      Polk Audio RTi100 Plate Amplifier won't power on and intermittently honks and buzzes
      by MrCommunistGen
      My childhood best friend was killed about 9 years ago. His parents are finally letting go of his things, and they offered me his Polk RTi100 tower speakers. The Polk RTi100 towers are one of a handful of designs from the early 2000s that is a full range 3-way tower with a built-in self-powered subwoofer. This is accomplished with a plate amp integrated into the speaker input panel.

      I think they used them for a while, but they've been sitting for at least a few years now. After about 40 hours of driving to their house and back (both they and I have moved in the last 9 years) I got...
      07-12-2021, 05:11 PM
    • jinu_j
      How to test Subwoofer Amplifier with only a multimeter
      by jinu_j
      Hi Folks

      Need some advice on how to test a subwoofer amplifier if i have access to only a multimeter.

      Problem
      I have a Boston Acoustics active Subwoofer (soundware S). Its rated output is 200W. But the output i am getting is very low i can barely hear/feel it even if put the gain at max. I replaced all the capacitors in the Subwoofer amplifier but still no change.

      Is there anyway to test this without getting an oscilloscope/Function generator to see if the fault is with amplifier, driver or the source??

      Any advice would be appreciated...
      08-29-2024, 02:05 AM
    • Loading...
    • No more items.
    Working...