PS4 Slim SAD-004 image request

[Rambonz]

Re: Ps5 three beeps when plugged in, no life

I was under the impression that on the disc editions, the bios contain the pairing keys with the daughter board. Did you flash it with a disc edition bios you found online or were you able to back it up and reflash first? otherwise, you would run into errors when trying to run a disc?

correct me if I'm wrong

[Rambonz]

Re: PS5 no 12v Power rail

Just for record-keeping for others.

Replacing the aonx38168 gave me back 12v power. I then found the TPS53219ARGTT Synchronous Buck Controller TI 3219A 5v Regulator was heating up so I replaced that as well.

At this point, I got 5v and 3.3v in f7002 however, on the reverse side of the board the SBV IC was getting warm and not outputting 1.8v (I believe it's 1.8v). The SBV IC in f7002 and on the opposite side of the board are the same chip, however F7002 was showing all voltages correctly, the opposite side of the board was not...

[Rambonz]

Re: PS5 no 12v Power rail



You wouldn't happen to know anything about this one as well by any chance? Looking for a replacement.

...

[Rambonz]

Re: PS5 no 12v Power rail

awesome, thank you!

[Rambonz]

Re: PS5 no 12v Power rail

Update on this for anyone that finds it useful in the future.

I got my thermal camera today and found the cause of the 12v rail's no power. It was this here. I am now looking for a replacement chip (EDM010 board chip numbers 38168 0A062C). I am also looking for replacement fuses F7501 and F7001. Anyone know where I can source them?

...

[Rambonz]

Does anyone have HDMI images of both sides of a SAD-004 PS4 slim board?

I have some missing components and I suspect a diode or two in the wrong place. A failed repair attempt from an acquaintance that I'm trying to salvage. Specifically looking for underside images of just above the HDMI port (not the pin side).

Cheers

[Rambonz]

Re: PS5 no 12v Power rail

Will do, cheers mate.

[Rambonz]

Re: PS5 no 12v Power rail

Ok, another few questions since I'm still a total noob (I appreciate not being roasted for these questions, I purchased this board from a friend to learn on).

First is anyone able to give me diode mode readings for this? And also tell me what it is supposed to be doing. BQZA0 chip. There's another one down by F3501 that reads differently.



Next, in diode mode, I get these readings. Are these voltage regulator IC's or MOSFETs or something else? (yellow dots are where I had black lead, red dot red lead, diode...

[Rambonz]

Re: PS5 no 12v Power rail

Ok thanks. I guess I need to look at the MOSFETS and caps just above them then. Does anyone have any experience troubleshooting in this area? I suspect given the putty placement if I introduce heat I'm going to lose some components here.

[Rambonz]

Hey guys

So I've got a ps5 EDM01 here that has no power on the 12v rail. I've noticed that on the back of the board by the power connector, I've got two components missing. Is anyone able to tell me what they are? My ESR meter is showing the other two as around 4pF and I assume they're just ceramic capacitors?



Cheers...

[Rambonz]

Re: New Members - please post your introductions here

Hey guys
I'm someone that's only recently picked up a soldering iron for video game console restoration. I'm from NZ. I've had a few successes and only a few failures so far, I'm pretty careful and methodical in my approach and tend to ask questions first. Definitely not a shoot-from-the-hip kind of tech. Anyway I hope I can share some of my experiences as I learn and ask some insightful questions!