Re: bush bpdp42hd3
how much do you want
futurespec
Member
Last Activity: 08-26-2018, 06:50 AM
Joined: 10-16-2013
Location: st.austell
-
bush bpdp42hd3
i turn my 42 inch bush on and red lights up and goes to green and i get six clicks and no picture can you help -
Re: toshiba 42wlt66 clicking no light
one of the pins that was soldered was broken so i re soldered it lower for the contact to work on the board
fully working nowLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
just re-solders ic chip and its works thanks mateLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
still the same unless the ic strw6765(q880) is faulty or needs a different oneLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
i have found that its the ic strw6765(q880) that i replaced first and have re-soldered and fergot to ad paste/i have pasted and soldered 3 pins together as from your photo i will try it again nowLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
ive had a look and have found that the SMPS IC Q880 mabe the problem
i can see from the photos where it says (q880) but can seem to work out if it the ic chip on the other sider or a mosfetLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
thanks for your help i will have a look and get back to youLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
do you know of any schematicsLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
where is the 5v standby output located on the main board and do i check at the ir sensor board to see if there is 5v to the board for the lightLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
i switch it on and dont get any standby light
will any of the caps need replacing on main psu board or is there any other common faults
that would narrow it downLeave a comment:
-
Re: toshiba 42wlt66 clicking no light
not sure where to start
pictures of the psu board...Leave a comment:
-
toshiba 42wlt66 clicking no light
i recently replaced ic chips on the psu board
i read a post about this problem
but i still get clicking noise
click turn on and nothing
no picture or sound
no red light for standby
nothing
does anyone have a clue
ic chips replaced
ic str-z4479
ic str-w6765
ic srx-2039
i changed these but nothing different -
Re: technika 32"
ive got hold of a complete set of boards speekers and cables for the technika 32"
[url]www.bixreclamation.co.uk[/url]
technika lcd32-600 32" lcd tv dealer service repair kit
all fully working nowRe: technika 32"<br /> <br /> ive ...ly working nowRe: technika 32"
ive got hold of a complete set of boardsLeave a comment:
-
Re: technika 32"
is there anywhere i can get hold of technika or unbranded l2m08(03) av boardLeave a comment:
-
Re: technika 32"
need to have a diagram or schematics to help meLeave a comment:
-
panasonic tx-p50u10b
Panasonic Viera 50" TV
It has a fault where it switches on then off again straight away and stays in stand-by mode.
model tx-p50u10b
can you help please -
Re: technika 32"
where the tv card goes i placed a fan there.
about 4 ic chips or more in that area is cooled with the fanLeave a comment:
-
Re: technika 32"
ive managed to use a small fan and soldered the wires to the av board and its been on for 2hours with sound fully workingLeave a comment:
-
Re: technika 32"
i cant use the file as i dont know what program to use to open it
where is the ic chip located on the board and you indicate to freeze the chip how would you do thatLeave a comment:
No activity results to display
Leave a comment: