Re: Complete Xbox 360 Recap?? (Polymer)
ended up not being to hard to pull them if I use the hot air to warm up the motherboard slightly & then using the 70 watt iron.
Thanks for all suggestions so far..
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Complete Xbox 360 Recap?? (Polymer)
the pad was not attached to the motherboard in any way, so there is no way to attach it to it.
I'm not sure how or why the pad wa loose, i went to grab it before I touched it with the Iron & noticed it..
here is a schem to the cap with the loose pad, its C5B7 (Bottom Center). Will it be ok to attach it to any GND? Or should I find & attach it to the GND side of C8B1?
[url]http://gyazo.com/d4b698c22e138cc6adea6c2db75faa86[/url]Re: Complete Xbox 360 Recap?? (Polymer)
...
Leave a comment:
-
Re: Complete Xbox 360 Recap?? (Polymer)
I'm slowly removing the caps and I noticed that one of them had the GND pad that was lose from the motherboard before I even touched it, so when I install the new one should I just run a wire from the closest GND point to the leg of the cap? Obviously it's nothing major because the console was still working before I started removing caps..
Leave a comment:
-
Re: Complete Xbox 360 Recap?? (Polymer)
No towel or heat method has been used, I've never had a issue with 360 but it is a launch day console so it is around 9yrs old and temp wise it used to run from 80c-85c. But I have 2 of the thermalright hr-03 heatsinks coming for it tomorrow so hopefully it will lower the temps some.
These are the heatsinks I will be putting on tomorrow. This console is a Jtag so I don't use a disk drive in it.
[B]As for my soldering station I have a 70 watt Aoyue 968A+ SMD Digital...Last edited by Morinzo; 04-24-2014, 07:59 PM.
Leave a comment:
-
Re: Complete Xbox 360 Recap?? (Polymer)
Two of the caps are swollen like the one on the left in the img below.
these are the yellow & black ones if they will help figure out what brand they are. You can see where I touched a soldering to one of the yellow ones by accident, lol.
...Last edited by Morinzo; 04-24-2014, 02:36 PM.
Leave a comment:
-
Complete Xbox 360 Recap?? (Polymer)
This is the original launch console and I'm wanting to try a complete polymer recap but don't know what values to use.
Could someone make suggestions on what brand, V, uf polymers to use to replace the following caps.
4 - 4v 820uf - Yellow & Black
15 - 16v 100uf - Nichicon VZ(M)
7 - 10v 220uf - Brown KY
9 - 16v 1500uf - KZJ
13 - 6.3v 2700uf - Rubycon MFZ
Thanks For Any Help!!
-
Re: Samsung UN46C5000QF (No Picture - Sound Working - Backlight Working)
I also noticed that there is no red light in the optical port when tv is powered on.
Edit: The red light comes on for 1 second at boot.
Not sure if this matters or not, just noticed that on my other tv's the red light stays on.
Edit 2: I found the service manual for this TV.
[url]https://docs.google.com/file/d/0Bwna7hZykYnndWhOS3Q3UUViVGM/edit?usp=sharing[/url]Re: Samsung UN46C5000QF (No Picture ... /> <br /> ILast edited by Morinzo; 06-30-2013, 05:04 PM.
Leave a comment:
-
Re: Samsung UN46C5000QF (No Picture - Sound Working - Backlight Working)
The fuse @ FP1 is good.
I have attached a few more pics for you.
Please help if you have anymore ideas, which board do you think is causing the issue?...Last edited by Morinzo; 06-29-2013, 08:33 PM.
Leave a comment:
-
Samsung UN46C5000QF (No Picture - Sound Working - Backlight Working)
Hi Guys,
Hope you can help with my issue, I can use a meter and soldiering is not an issue.
I have a Samsung UN46C5000QF that has sound and no picture. I have attached a picture of the T Con board and the backlight working. If you need anymore pictures let me know
I turned the TV off this morning when I left for work this morning and it was working fine & when I got home this afternoon I turned it on like normal and it makes the Samsung Boot Noise and i can hear the sound from the cable box or the xbox360. I can't see anything but i can turn it up and...
No activity results to display
Show More
Leave a comment: