Re: Panasonic TC-L47E5 LED TV blinking red power light PLEASE HELP
the problem with that is this set does not have any legends on the boards also it goes into protect mode so I cant even measure voltages....
sergio2013
Senior Member
Last Activity: 10-16-2013, 11:46 AM
Joined: 03-26-2013
Location: Winnipeg/Manitoba
-
Re: Panasonic TC-L47E5 LED TV blinking red power light PLEASE HELP
Still need help on this one. Anyone know what I can check? the service manual says the one blink is the panel inverter. I replaced the LED driver board which i'm assuming is the inverter and its doing the same thing.Leave a comment:
-
Panasonic TC-L47E5 LED TV blinking red power light PLEASE HELP
I push the power button and the power led turns a solid red as if its trying to turn on the just starts flashing red infinity with a one blink code with a few seconds pause in between and just keeps doing the same thing over and over. Any Ideas? what does a one blink code mean on this model anyone know? -
Re: Samsung PN50A450P1D Plasma vertical lines any ideas? please help
Its ok I figured it out and had a successful repair. Thanks for your help....Leave a comment:
-
Re: Samsung Plasma E-Buffer board Fuse PLEASE HELP!!!
That's what I did and it worked out great. Thanks for all your help....Leave a comment:
-
Re: Samsung Plasma E-Buffer board Fuse PLEASE HELP!!!
Maybe I wont try that then, what would be the best way in removing it with just one heat gun...Leave a comment:
-
Re: Samsung PN50A450P1D Plasma vertical lines any ideas? please help
Ok, any tips for unsoldering the faulty one and soldering the new one in place? I have one here from a digital board I don't need its exactly the same specs and same fuse. I assume its going to be had with an iron that can only heat up one side at a time. I'm scared of lifting the pads or burning them. Any tips? how about soldering the new one on top of the old one? Do you think a heat gun would work to melt both sides at the same time to pull off the fuse with tweezers...Leave a comment:
-
Re: Samsung PN50A450P1D Plasma vertical lines any ideas? please help
Actually its the The fuse in my Samsung Plasma E-Buffer board is blown because of a power outage in my house. I jumped the fuse for a few minutes to see if the set was fine and it was. How safe is it to just leave the fuse jumped? would it be ok? If not I have included a picture of the fuse....Leave a comment:
-
Re: Samsung Plasma E-Buffer board Fuse PLEASE HELP!!!
Do you think a heat gun would work to melt both sides at the same time to pull off the fuse with tweezers...Leave a comment:
-
Re: Samsung Plasma E-Buffer board Fuse PLEASE HELP!!!
Ok, any tips for unsoldering the faulty one and soldering the new one in place? I have one here from a digital board I don't need its exactly the same specs and same fuse. I assume its going to be had with an iron that can only heat up one side at a time. I'm scared of lifting the pads or burning them. Any tips? how about soldering the new one on top of the old one?...Leave a comment:
-
Samsung Plasma E-Buffer board Fuse PLEASE HELP!!!
The fuse in my Samsung Plasma E-Buffer board is blown because of a power outage in my house. I jumped the fuse for a few minutes to see if the set was fine and it was. How safe is it to just leave the fuse jumped? would it be ok? If not I have included a picture of the fuse so someone can tell me what type of fuse it is. I know its specs, but I don't know what kind it is. Is it a pico fuse?... -
Re: Samsung PN50A450P1D Plasma vertical lines any ideas? please help
Well I was having success with the lines I got them to disappear, but as I was about to close it up I heard a pop and I seen a spark and after inspection I see what blew, I'm not sure but it look like to be a capacitor on the logic buffer E which the buffer looks like its not replaceable cause the ribbons to the screen are attached to it, anyhow I took a picture of what blew you can see its burnt in the picture also the number on the board of the failed part is C2555 is that replaceable by soldering a new one and...Leave a comment:
-
Re: Samsung PN50A450P1D Plasma vertical lines any ideas? please help
Ok thanks ill give it a go and ill report back my findings....Leave a comment:
-
Re: Samsung PN50A450P1D Plasma vertical lines any ideas? please help
Ok ill try that, when you say digital board do you mean the main board or the Y-Buffer? also does it look like a bad panel or no?...Leave a comment:
-
Re: Samsung 50" Plasma PN50A450P1D vertical lines
Did you figure out what the problem was? I have the same problem.Leave a comment:
-
Samsung PN50A450P1D Plasma vertical lines any ideas? please help
Samsung PN50A450P1D Plasma vertical lines any ideas? please help. I attached pictures, the lines go from the top to the bottom of the screen and just on the right hand side....Last edited by sergio2013; 08-31-2013, 04:46 PM. -
Re: Samsung LN40D630 LCD TV, Backlights lit, but no display, please help
Just got the T-Con board put it in and bam the TV is working, so it was the T-Con board that was faulty. Thanks for all your help guys....Leave a comment:
-
Re: Samsung LN40D630 LCD TV, Backlights lit, but no display, please help
Ok will do and report back when the new T-Con arrives. Thanks for your help....Leave a comment:
-
Re: Samsung LN40D630 LCD TV, Backlights lit, but no display, please help
I checked and I don't see anything with a P, but I see one with a N labled C_DF1 and its white. is that it? I did a Ohm check on that part and my multimeter is telling me its shorted....Leave a comment:
-
Re: Samsung LN40D630 LCD TV, Backlights lit, but no display, please help
Ok here are the results
GMA 1 = 17.04
GMA2 = 14.01
GMA3 = 13.26
GMA4 = 12.43
GMA5 = 12.11
GMA6 = 11.69
GMA7 = 11.33
GMA9 = 9.73
GMA10 = 8.22
............
GM1 = 16.97
GM2 = 14.04
GM3 = 13.26
GM4 - 12.42
GM5 - 12.11
GM6 = 11.72
GM7 - 11.33...Leave a comment:
No activity results to display
Leave a comment: