Re: Problem with my HANNS G HG281D
Hello,
Thank you for your answer.
I changed the two big ones as shown in the picture and the three little ones. They weren't bulged but I changed them because I saw in the forum that it is better.
I'll have a look to see if there is shorted components and I'll telle you.
Thank you...
axl1
Member
Last Activity: 10-14-2017, 05:15 AM
Joined: 03-24-2013
Location: Paris
-
Re: Problem with my HANNS G HG281D
Do I have to change the whole card where there is the burned component?
But if I do, it wont do it again ? Does it come from the card before? Non one has an Idea?Leave a comment:
-
Re: Problem with my HANNS G HG281D
Hello,
No one can help for the burned component?Leave a comment:
-
Problem with my HANNS G HG281D
Hello guys,
Hope you are fine.
I have an issue with my HANNS G HG281D.
It began like this: it wasn't possible to turn it on. I changed two caps that were bulged and anothers.
When I turned it on, the green led turned on blue,the screen became blank for one second and after that became black. The led changed to orange.
There was a smell of something burning. So, I found what burned and you can see it in the picture below.
Is it possible that this component burned because of card where I cahnged the caps?
Is it possible to repair ir?
...
-
Re: Hanns_G HG281D
Hi guys
I'm back. I bought the caps and changed them. I changed the ones shown in the post 428 and it works great
I'd like to thank you all for your patience and kindness.
This a great forum.
Thank you very muchLeave a comment:
-
Re: Hanns_G HG281D
Hi
Thank you for your answer. The board were not all attached.
I'll try again this evening and I'll tell you.
Thank youLeave a comment:
-
Re: Hanns_G HG281D
I post another picture with the new zero volt....Leave a comment:
-
Re: Hanns_G HG281D
Please answer me for the voltage I find. They are written in the picture.
There are also two caps near the big cap. One of them gives 0 Volt !
Is there another problem except caps?
Thank you.Leave a comment:
-
Re: Hanns_G HG281D
Hello,
Mariushm, thank you for the links and your advice. The links looks interesting. I wanted to buy from Ebay but I prefer your links.
As suggested by Lumberjack777, I'll begin by the caps of the post 428 and if it doens't work, I'll replace the ones of the logic board.
I took some measures and the results are on the picture below.
Could there be some other problems to have such results? I find zero volts at some caps and two fluctuating values !
Thanks a lot....Leave a comment:
-
Re: Hanns_G HG281D
Hello
Here are the caps I have to buy:
10V 1000 uf
10v 1000 uf
25v 1000 uf
25v 1000 uf
35v 1000 uf
25v 470 uf
10v 470 uf
35v 470 uf
10v 470 uf
25v 470 uf
50v 47 uf
400v 22 uf
35v 22 uf
35v 22 uf
35v 22 uf
50v 10 uf
35v 10 uf
50v 2.2 uf
100v 1 uf
But they are sold by lot and I can't find all these values. Sometimes, the voltage is different. Can I buy different...Leave a comment:
-
Re: Hanns_G HG281D
Thank you very much for your post. You have a good sight. I did'nt see it.
I'm going to read the thread you told me and thank you your advice.
I'll give you some news when I'll change them.
Thank youLeave a comment:
-
Re: Hanns_G HG281D
Hello
Thank you for your answer and compliment
I took two pictures and excuse me for the light but there's not enough sun in Paris lol.
I forgot to say that when I unplug, the voltage in the main capacitor decrease about 3 volts per second.
If you need other pictures, i'll be glad to post others.
Hope you can help.
Thank you...Leave a comment:
-
Hanns_G HG281D
Hello,
First, I'm from France, so excuse me for my english.
I've a Hanns-g HG281D and there's no power. The power LED stays off. It began by trying more than 10 on the power switch to turn it on and now, it doesn't start at all. The switch is good. I checked the secondary voltage on the connector between the power board and logic card and I find 0v. I find 320 V at the main capacitor. Perhaps it's good because in Frace, the power supply entry is 220v.
Have any idea?
Thank you
No activity results to display
Leave a comment: