User Profile
Collapse
-
It must be the battery itself that's faulty. I just went back to measure the battery connector pin JBATT1.7 (SMBUS SDA):
- No battery connected, adapter only: 3.5 V
- Connect battery only: 2.3 V
Not sure how I missed this before. I don't know if I can do anything about this or the best option is to return this battery and get a new one. This is a replacement battery I bought off Ebay.Leave a comment:
-
Leave a comment:
-
Removed all power, measured the mosfets in resistance mode, 200k setting. Measured both ways (here first measurement with red on first pin, second measurement black on first pin)
PQ201
• drain ↔ source: 181 kΩ / 61 kΩ
• gate ↔ drain: OL / 185 kΩ
• gate ↔ source: OL / 107 kΩ
PQ202
• drain ↔ source: 130 kΩ climbing to 200 kΩ / 61 kΩ
• gate ↔ drain: OL / 109 kΩ climbing to 200 kΩ
• gate ↔ source: OL / 89 kΩ
PQ203
• drain ↔ source: 30 kΩ climbing to 120 kΩ / 60 kΩ
• gate ↔ drain: OL / 150 kΩ climbing...Leave a comment:
-
Some more testing done on the SMBus data line EC_SMB_DA1, in order to understand if it should read 2.54V instead of 3.3V:- PC off, only battery connected: 2.54 V
- Power cable connected, battery connected: 2.54 V
- Turning PC on with cable connected and battery connected: PC turns on normally. Removing the cable, PC stays on battery power only. (this previously didn't happen, PC would shut off immediately when cable was removed). After a few minutes, turns off abruptly.
- Without power cable connected, no sign of life when pressing the power button. On cable, LEDs light up and
What else...Leave a comment:
-
DA0PAMB16A0 Rev A, Quanta OPA, HP 14s-fq, AMD 3020e - Request schematic and Boardview
DA0PAMB16A0 Rev A, Quanta OPA, HP 14s-fq, AMD 3020e -
Unplug the battery, only charger:
EC_SMDA (Green): 2.54 V
EC_SMCA (Blue): 3.3 V
Battery plugged:
EC_SMDA (Green): 2.3 V
EC_SMCA (Blue): 3.3 V
If I understand correctly, also EC_SMDA should be at 3.3V, so this is an anomaly. Following the schematics, this line is connected to PD103 pin 3, then a PR106 100 Ohm resistor (measured and shows 100 Ohm). From there (EC_SMB_DA1), it seems to be connected to PU201 and also to the EC chip through this RPE2 resistor array. PR217 is not present on this board however, meaning it's not connected to the PU201?...Leave a comment:
-
[QUOTE=mon2;n3954563]Yes, PR209 is defective and should be replaced. Then test again.
Pulled out PR209 from my old board, measured it (10R exactly) and replaced it. Measured again, exactly 10R and remeasured everything else (current sensing resistor on pins 19, 20 still 20R; battery mosfet has 11.5V, VCC power pin has voltage), everything seems correct. Checked main power rail in other parts of the board and voltage 11.5V was present. Looks like from the power perspective everything is fine?
As mentioned, on cable PC works completely fine. With battery connected,...Leave a comment:
-
Does this battery have a voltage at this time?
Yes, came back now after a few hours and battery is holding it's charge at 11.3 V (close to its rating 11.52V)
Remove all power. Disconnect the battery. Use the lowest resistance scale on your meter. Measure the resistance between pins 19 & 20 on the charger IC @ PU201. What is the exact resistance? Touch your meter probes together. This is your baseline measurement. Subtract this value from the above measurement for the true resistance.
The true resistance should be ~20R ohms. Confirm it.
Touching...Leave a comment:
-
The battery model is L17M3PG2. In fact on YouTube Electronics Repair School had a bunch of videos with a similar case, and in each one he ended up using a special analyser to fix the issue. I would like to not invest 450€ for this tool though.
Removed the battery and measured resistance with black probe on pin 1 GND.
1, 2, 3, 4 (GND, black): OL
5 (NC_2756, yellow): not connected
6 (BATT_TEMP_IN, white): 10 kOhm
7 (EC_SMDA, green): OL (in the megaohm range)
8 (EC_SMCA, blue): OL (in the megaohm range)
9, 10, 11, 12 (VMB, red): OL...Leave a comment:
-
Lenovo Legion Y530-ICH15: works with power adapter, but not off of the battery
Hello, I need help understanding why my PC is not recognizing and working with the battery.
Lenovo Legion Y530-ICH15: works with power adapter, but not off of the battery- Replaced battery with a new one off eBay, connected adapter and battery initially read 0V
- Injected 10V 1A on the battery connector, which started pulling 1A and suddenly started reading 11.54V (that's the rated voltage of the battery)
- PC still does not start only from battery
- Measured that 11.54V does reach the power regulator chip, which is on the underside of the board though, so I'd have to pull the board
-
> What is interesting is that mine do turn on when I press the power button, so keyboard and power button working. And SOMETIMES it does POST, but even if I enter to BIOS it shuts down in like 20-30s or so.
Yeah, it was similar for me. In my case it would randomly boot up after a power reset, stay on for some time with no image, but it would stop doing it after a few tries. I tried a trick (demonstrated in one video by Sorin) where you use hot air to "boil" liquid flux along the edges of the CPU. As result, the PC for the first time booted normally into Windows. It worked... -
unimatrix93 yeah, mine is exactly the same case in this video (https://www.youtube.com/watch?v=B1U3n9DstPo). It's a broken connection under the CPU caused by this black epoxy Lenovo uses and solution is CPU reballing. I'm considering whether to try this, since I would need to get some additional equipment, but the symptons are exactly these.Leave a comment:
-
Got it. After some more inspection on mine I found that mine actually does turn on. Client had reported a motherboard fault, but actually the 300W Lenovo power brick had died.
It seems it caused some sort of damage though, because it only turns on when computer is held at an angle. It also turns off after 20-30 s abruptly (as if the button was held down).
Seen something like this before?...Leave a comment:
-
Hi Green Probe, I have the same 16ACHg6 with the exact same issue: rails present, battery charging, back LEDs on - but doesn't power on. Did you find out what was causing the issue for you?...Leave a comment:
-
Update
Got the freeze spray and did a bunch of injection tests (at 0V8 this time) on +3VALW and +1.05VALW rails (monitoring the current draw, which did peak = shorted). Sprayed and monitored all components on these rails on both sides of the board, but nothing got noticeable hotter (checked also under CPU and GPU as recommended). Not sure if this is can happen, also I wonder if I would be able to detect something better if I had a thermal camera. (don't want to buy yet another 150EUR tool at this point yet).
Not sure if there is any more measuring I could do at this point. Current...Leave a comment:
-
Thanks for the pro tip and now that you mention it, it makes total sense. Will keep this in mind and will update the thread if I find anything new. Thanks!
No activity results to display
Show More
Leave a comment: