Re: Samsung PN51D550C1F - Clicking...HELP!!!
Any suggestions??
ptheman12345
Member
Last Activity: 09-10-2014, 03:53 PM
Joined: 12-27-2012
Location: Miami, Florida
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
i also noticed that after replacing the old Ymain with the new one, the panel flashes once when plugged inLeave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
When I plug the tv in, at the first click, Vs is about 207 and Va is about 58. As for Vsc, it was about -195. The control board has a slower blink about every 5 seconds. I bought the Ymain from shop jimmy, so it should be working...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
I just installed the new Y-Main, but the TV still isn't working properly. The relay clicking stopped, but nothing is appearing on the screen. Could there be another board that is bad?...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
Yes, it's the same reading I get when the probes aren't touching....Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
When doing pins 2-3 on certain diodes, I would get a reading of 1. I'm prettying sure I followed your instructions correctly. Would that mean the board is bad?...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
I've attached a pic of the bottom of the X-Main...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
Sorry. How do I go about doing that?...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
I'm gonna go ahead and order the part. Hopefully it works. I'll report back once the part comes in. Thanks for all your help TOM!
...
Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
I located it. Its LJ92-01764A. Should I go ahead and order the part or are there more testing that can be done to make sure its the Y-SUS thats causing the problem?...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
When the X-Main is unplugged, VS-TP was measured at 1.1V and VA-TP was measured at 0V...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
When the Y-SUS board is unplugged, VS-TP was measured around 200V and Va-TP was measured around 58V. Both started to drop after the first click stopped...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
When unplugged, both read to be 0.0V. During the clicking cycles, I measured VS-TP to be 1.3V and VA-TP to be 0.0V...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
Yes I do...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
How do I test if the Y-SUS board or buffer is bad?...Leave a comment:
-
Re: Samsung PN51D550C1F - Clicking...HELP!!!
Attached are pictures of the boards...Leave a comment:
-
Samsung PN51D550C1F - Clicking...HELP!!!
My Samsung PN51D550C1F just started clicking when powered on and I can't seem to figure out whats wrong. I've searched through the forum to see if anyone has came across this problem, but I've found none so far. If someone could help me find a solution to this, that would be so great Please and Thank you!
-
Re: Samsung pn58b860 Clicking
Finally found time to do the test and here are the results: After using a 330 ohm resistor and following your steps, I got the colored test patterns after jumping pins 3-4 on the control board. Just placed an order for a new main board. I'll report back with the results after it comes in. Man, I hope it works!Leave a comment:
-
Re: Samsung pn58b860 Clicking
yeah, how do i go about doing that?Leave a comment:
-
Re: Samsung pn58b860 Clicking
okay, I'm going to go ahead and order a new main board. Hopefully thats the cause of the problemLeave a comment:
No activity results to display
Leave a comment: