Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
-
Re: Samsung ps42 q7hd plasma display problem
No i have not run the self test , how is the self test enabled ? i am not sure how to do it.
Leave a comment:
-
Samsung ps42 q7hd plasma display problem
Hi does any one have any advice as to which board is most likely bad here....
-
Panasonic TNPA 5105 SC boards.
Could any one please advise me if the TNPA 5105 Sc boards from a 46 inch or 42 inch Panasonic Plasma will work in the 50 inch Panasonic plasma.
-
Re: Panasonic TXP50 S21 B
I have just done a few quick tests and found the resistance across the SC board power connection is 12 ohms , the reading across the SS board power connector is around 1 .3 Meg Ohm. Does this seem too high a resistance across the SS board supply ?
Leave a comment:
-
Panasonic TXP50 S21 B
When this Tv is switched on the relay is heard to click , the tv won't come to life , the front LED flashes 4 times.
-
Re: Samsung PS43 E4501W Plasma Tv
I will post some really high quality close ups soon , once i get new Duracells for my proper cam. Samsung PS43 E450 - 1WLast edited by Techstar; 08-16-2017, 01:54 AM.
Leave a comment:
-
Re: Samsung PS43 E4501W Plasma Tv
A few pictures of the board. X - Main seems to have been incorporated into the PSU. My phone camera sucks , I can't get good pictures. I will get me some battery's for my Digital Camera asap....
Leave a comment:
-
Re: Samsung PS43 E4501W Plasma Tv
This is not that old , the date is November 2012. I have unplugged the X - buffer and the short has gone...
Leave a comment:
-
Re: Samsung PS43 E4501W Plasma Tv
The VS supply to the Y main board is showing short circuit. I have disconnected Y-main but the short circuit is still there.
Leave a comment:
-
Samsung PS43 E4501W Plasma Tv
This is dead and flashing 2 blinks on the front LED . Does anyone know what this fault may be.
-
Re: Lg 50pq3000
Check diode D352 on the power supply board it may be short circuit.
i had this fault once before on this model.
Leave a comment:
-
Re: Help with xenius lcd42
I just repaired a dead xenius tv the, exact same model yesterday , re-capped all of the power supply board , most of the electrolytic caps read bad on my Capacitor & ESR Meter.
The picture quality on these sets is not too good though. The plastic frame of the telly is real flimsy poor build quality too.
Leave a comment:
-
Re: Sharp LCD 32DH57E No power up.
I have been looking at the connector pins on P7201 for the BL-ON pin , i can't make out which pin should be sent high to turn on the lights.
Could you advise what turn on voltage needs to be applied to which pin please .
Leave a comment:
-
Re: Sharp LCD 32DH57E No power up.
Should the inverter board have switched on after forcing the power supply on, i am not too sure. ?
Leave a comment:
-
Re: Sharp LCD 32DH57E No power up.
I have decided to salvage all good parts off this tv and scrap it.
A good screen too , if anyone needs the screen message me.
Leave a comment:
-
Re: Sharp LCD 32DH57E No power up.
Not another main board problem :-(
Leave a comment:
-
Re: Sharp LCD 32DH57E No power up.
There is 56 . 2 Volts at both sides of the fuse , i have measured the voltage as far as JA102 this is a wire link on the same rail as the fuse. The fuse appeared to have a solder crack where it is soldered to the board , i have resoldered it but the set remains no go.
Leave a comment:
No activity results to display
Show More
Leave a comment: