Sounds good... Thanks for your help.
stepka
Member
Last Activity: 08-03-2016, 10:04 PM
Joined: 12-19-2012
Location: Shakopee
-
Re: Panasonic plasma TC-P42C2 10 blinks
Sounds good... Thanks for your help.
-
Re: Panasonic plasma TC-P42C2 10 blinks
Sounds good... Thanks for your help.Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
Thanks for your help! Is there any way to replace whats necessary on each board? I can solder.Last edited by stepka; 07-31-2016, 12:59 AM.Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
The board has been removed from the TV for testing. Here are my readings (e post = right , g post = left and c = center)
Q021 Right-left = 14.2ohms, center-left = 14.3, center-right = 1.2
Q022 R-L = 11.9, C-L=11.7, C-R = .9
Q001 R-L= 22.6, C-L = 22.6, C-R = 1.4
Q002 R-L = 21.6, C-L = 22.1, C-R = 1.4Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
RJP30E4 at Q001, Q002, Q021, and Q022 all beep (only the outer 2 tabs are connected to the board) when i touch any if the 3 tabs.Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
3a and its a constant beep...Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
Q661 will beep when I connect any two of the three posts, no matter what sequence I do.Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
It's a Craftsman 82372 meter and I'm not sure if it has any of those modes, but I can set it up to beep if I touch the 2 probes together.Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
There is resistance on when I checked the 2 pins on the SN2 connector. I dont know how to check for a shorted leg.Leave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
Thanks for the reply. No error. Yes I do have a multimeterLeave a comment:
-
Re: Panasonic plasma TC-P42C2 10 blinks
BumpLeave a comment:
-
Panasonic plasma TC-P42C2 10 blinks
Hello everyone, I've read everything that this site and Google has to offer but I haven't found an answer. I have a TV that I acquired (model in subject) and it blinks a code 10. I unplugged the SN2 and SS11 connectors and it still blinked 10, then I plugged in SN2 and I blinked 7... Please help -
Re: Sony KDL-40S2000; on 10 min then 4 blinks
Well, this is weird! After reinstalling the inverter boards and power supply its working fine. Its been on and off for more than 3 hours with no issues. If it start acting up again I will bump this post.Leave a comment:
-
Re: Sony KDL-40S2000; on 10 min then 4 blinks
Any ideas?Leave a comment:
-
Re: Sony KDL-40S2000; on 10 min then 4 blinks
Inverter boards...Leave a comment:
-
Re: Sony KDL-40S2000; on 10 min then 4 blinks
Power Supply...Leave a comment:
-
Sony KDL-40S2000; on 10 min then 4 blinks
I picked up this tv from a co-worker for $25 in hopes for a cheap and easy fix, or it's gonna be a parts tv. My co-worker said that it started acting up after a storm. It will power up and run fine for about 10 minutes then the screen wil flicker a few times and then shut off and blink 4 times. It will start up again after 30 min of being unplugged. I have searched all of Google and nothing "easy" has worked, so it's time to dig deep. -
Re: Samsung LN32A450C1D will not turn on - steddy red light
OK, gotcha!Leave a comment:
-
Re: Samsung LN32A450C1D will not turn on - steddy red light
IPA.. You mean a beer?Leave a comment:
-
Re: Samsung LN32A450C1D will not turn on - steddy red light
I checked out the area that you circled and I think you're right. The glue was dark in color at the top of that part. I also noticed that the solder was pretty weekly done. I removed, cleaned, and re-installed the part... lets see how long it lasts....Last edited by stepka; 05-16-2015, 01:01 AM.Leave a comment:
No activity results to display
Leave a comment: