Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
The Power Adapter when i connect to another good PAP2T that working fine from last 2 months. Power Adapter is fine.
And i change another Power Adapter and connect to this PAP2T, still same problem.
But still you want then i will check, please let me know, how to check Power Adpter.
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
I don't know which one is the Electrolyte Capacitors. So i use the one which you mark for GROUND on IC that is PIN1 then i got readings below
U11 -- Pin2 : 0.76, Pin3 : 1.66,
U12 -- Pin2 : 0.63, Pin3 : 1.53,Last edited by tester2; 12-10-2013, 12:12 PM.
Leave a comment:
-
Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
on my Multimeter, where i have to Adjust in VDC, please let me know. Can i Adjust 20V DC.
UPDATE :
I Power ON PAP2T then i touch Black Probe to GROUND & Red Probe to Pin 2 & 3 on both IC's, there is no reading shows. it shows just 0.00.Last edited by tester2; 12-10-2013, 11:50 AM.
Leave a comment:
-
Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
Please make me correct in the pictures
Picture 1 & 2 where i mark, that is same pin, can i use that for GROUND purpose.
Picture 3 & 4 where i mark, can i assume that is Pin2 (V out) & Pin3 (V in).
Thanks...Last edited by tester2; 12-10-2013, 11:31 AM.
Leave a comment:
-
Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
hi there, here it is the part numbers
U11 -- AMC1117, F0823J
U12 -- AMC1117, F0823J
both of them having same part numbers, i look very carefull, there is no mistake in part numbers, i use a lense which is use to fix WATCHES, so i put board close to my eyes and i read with lenses clearly.
When I order SMD REWORK STATION i order this Glasses also, so i have all the instruments to check the BAD parts.
Thanks...Last edited by tester2; 12-09-2013, 09:17 AM.
Leave a comment:
-
Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
hi there, please let me know, by using multimeter RED Wire led & BLACK Wire led where i have to touch on U11 & U12 pins.
And on which reading I have to adjust my Multimeter Pointer for example 2000K etc. I am having exactly same this Multimeter.
I already saw U11 & U12 on my Board.
Please how to check this is good or Bad, then i will check and post my result.
Thanks...Last edited by tester2; 12-08-2013, 09:20 PM.
Leave a comment:
-
Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
hi guys, sorry for the delay, because i order "Soldaring Rework station smd 898D",
So i resolder the above as shown in Post#4, still I am having same light are ON. As well as I did HOTAIR Flow over the Chip also, still same 1 red & i green light ON.
So i like to know "How to check which component is Damage on the Board",
Can any body let me know the procedure to check Component on the Board, then i will check one by one.
Thanks
Leave a comment:
-
Re: My ATA PAP2T-NA Adapter Bricked, I want to fix
hi there, i apparicate for your reply.
do you think my board having same issue, or on my board a CHIP which hold software having poor soldaring, i even don't know where is the CHIP on this Board & where is Q156 located.
And you board having issue about "Loude Static", but my board having diffrent issue, i think my board having issue of loading software while rebooting PAP2T, so it is showing 1 Red & 1Green Light.
Thanks
Leave a comment:
-
My ATA PAP2T-NA Adapter Bricked, I want to fix
hi guys i need your help, i got PAP2T-NA which is not working, just hang on 2 Lights on it 1 is Red & 1 is Green.
So i like to know how to fix this PAP2T.
I am attaching Photo, please have a look.
As well as I attach the Picture of PAP2T Motherboard.
Hopefully waiting for your reply...
-
My ATA PAP2T-NA Adapter Bricked, I want to fix
hi guys i need your help, i got PAP2T-NA which is not working, just hang on 2 Lights on it 1 is Red & 1 is Green.
So i like to know how to fix this PAP2T.
I am attaching Photo, please have a look.
As well as I attach the Picture of PAP2T Motherboard.
I notice my Photos unable to attach, which i have in JPEG format, so how to attach Photos.
Hopefully waiting for your reply
Thanks.Last edited by tester2; 08-18-2013, 10:01 PM.
-
Re: Xbox360 shows E74 error on TV Screen, how to fix
hi guys, i did Oven Cook today for 2 hours 15 minutes, after done that, then i connect to TV. Now when i power ON then for a second i saw "xbox360 screen only one time" then i am getting Right side bottom 1 red light on for a second, there after this light goes off then on Left side i am getting 2 red lights ON continously, & on TV nothing shows.
so there is no more E74 error on tv, just black screen shows, so what i can do in this situation, hope i get some success, if you guys give me some advice....
Leave a comment:
-
Xbox360 shows E74 error on TV Screen, how to fix
hi guys i need your help, i got xbox360 shows E74 error on TV screen. so i did the following things, still not success.
1)-i did x-clamp on to heat sinks with thermal past etc, still i am getting same error E74.
2)-i did this back on the board, i remove 4 elastic white past (by manufacturar comes this elastic white paste there) & i put thermal past treatment then reattach that 4 elastic paste back on it, still E74 error shows on TV.
based on your experience, what is the best solution to fix this error. and its look like software error may be, because...
No activity results to display
Show More
Leave a comment: