Mailf
Member
Last Activity: 12-17-2024, 04:45 PM
Joined: 12-06-2024
Location: Netherlands
-
Or this one ? RJK0389DPA -
This one maybe ?
FDMS0308AS​ n chanelLeave a comment:
-
This one maybe ?
FDMS0308ASLeave a comment:
-
Thanks today ill get my hot air station.
I have allot of donor boards, how to know which i can use ? My acer has the pk5n2ea...Leave a comment:
-
Thanks, I tried to remove the mosfet but that didnt work with solder iron so i need to buy hot air station. It melted a little but now my ac adapter doesnt go into protection mode anymore
For the first time ill get 19v on the dc jack and the mosfet, however only 0.5v on the other side.
So need to wait for my hot air station first...
Does this means the short is gone? And now the mosfet is just broken or something ?​Leave a comment:
-
Yes in diode mode source to gate 005
Source (dot) to drain all 000Leave a comment:
-
Thank you i first need smaller probes...
For the first mosfet is it normal to have pin 1 (with dot) connected to all other pins on other side ? 001 in diode mode
Theres only resistance between the dot and gate 005 [ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3527634}[/ATTACH]...Leave a comment:
-
Where starts pin 1 on pub 1 ? i dont have any schematic of this pub1 and cant find one either.
The voltage with the non original adapter that does not ahuts off does not get higher than 0.4 to 0.9 v from the powerjack and the first mosfets, so is the voltage important then on pub1?
First of all all thanks for your help....Leave a comment:
-
About the mosfets i dont know what 1 to 8 is ?
this is the mosfet reading in 20k mode
0.05 and the other 0.06
Isnt that way to low ?
[ATTACH=JSON]{"data-align":"none","data-size":"thumb","data-attachmentid":3525808}[/ATTACH]...Leave a comment:
-
Prb3 is that clr ? 005 in diode mode...Leave a comment:
-
Yes seems my main rail is shorted. the clr is 0.00 on 200k mode, or 0.004 in diode mode without beeping mode....
And most inductors are also 0.00 ground on 200k ohmse, and 0.004 to 0.009 in diode mode (it changes every time)
All red is 0.00 on 200k ohm mode...Leave a comment:
-
All these things get hot circled, second mosfet most... (Image)
first mosfet 1 probe to ground all pins 500 ohm range
2nd mosfet 500 range input side other side all 4 pins 003
What does this say?...Leave a comment:
-
I tried another adapter that does not go in safe mode from another laptop this gives 0.4-0.9 v on the dc jack and the first mosfets.
This is the jack.
I have allot of other cabled dc jacks, is it possible to solder the red and black wire to the board to test out if the problem is the dc jack ?
Dont know where to solder it on ?
This jack has so many pins...Leave a comment:
-
Acer nitro 5 an515-55 dead
Hello i have acer nitro 5
AN515-55
Fh51m la-j871p
rev: 1b
Does nothing at all, no bootup, no power ligts, no charging lights nothing.
It just suddenly died
My batter was always good, now reading 0volts
I have no power on de dc jack, when i plug in the charger the charger turns off..
How can i test if the dc jack is bad and the rest wil work ?​ -
Hello guysLeave a comment:
No activity results to display
Leave a comment: