Re: Charge 50cc scooter battery with 12v plug?
Its an automatic scooter. I'll just borroa a charger. Not got my CBT until Friday so plenty of time to get it started. Thanks guys.
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Charge 50cc scooter battery with 12v plug?
Is it possible? Without blowing up.
I have a 12v 3A adapter, can I use it to charge it up? Its a 12v battery.
I have no kick start and battery has gone dead.
-
Re: Altec Lansing iMT320, badcaps!
its a pain in the bum. got to remove the leather case thing. its stuck down with glue.
Leave a comment:
-
Re: Please help me with HDX18 CPU upgrade gone wrong
Its over heating. You either used too much or too little thermal compound.
The fan is a clear indicator, it should not be running that fast when you have just switched it on.
It goes off when booting windows because the cpu is under more stress and getting even hotter, go into bios and check cpu temps.
Leave a comment:
-
Foxconn A74ML-K wont post but fans spin.
Got this off ebay for £1, came with a heatsink and amd sempron 140.
[url]http://www.foxconnchannel.com/ProductDetail.aspx?T=motherboard&U=en-us0000467[/url]
She said it worked fine one day and not the next.
When i got it the cpu pins were bent, I have bent them back and tried the cpu in my motherboard and it works fine, i have also tried my x6000 cpu in the foxconn but it still wont boot up.
I get no beeps.
The cmos battery was dead, and it doesnt charge up when left in the socket.
Tried a known good cmos battery...Last edited by gilly1984; 03-18-2013, 03:45 AM.
-
Re: Laptop only boots after bios reset?
I don't have the laptop to hand until tomorrow.
the laptop works great when switched on. it works on battery and on ac. it charges the battery fine too. the only problem occurs when I shut it down, I have to reset the bios before it will switch on again.
I will tinker tomorrow when I have it in my possession.
Leave a comment:
-
-
Laptop only boots after bios reset?
Got a lappy off ebay that needed the charging port resoldering.
Did that and it worked fine, but upon shutting down the only way to boot it back up is to remove the battery, press power button, put battery back in and then press power button again and it will boot fine.
When I got it I put a dual core cpu in it, this was before the charger arrived so I didnt test it before with the original cpu in it. Could this cause it?
It also had vista installed but I put windows 7 on it instead, again, I didnt test it before the charger arrived. Could the wrong...
-
Re: Baird X47DTV power supply issues
and pop goes my new 18n50. soon as the backlights tried turning on it buzzed and popped the fet and fuse. I think the transformer is broke somehow?
bought PSU off eBay instead.
will use this broke one for spares for when mine breaks again.
Thanks again Tom.
Leave a comment:
-
Re: Baird X47DTV power supply issues
Ok Thank you.
Also Tom, while you are still responding to this long Bairded thread.
When you helped me fix my tv last time it worked fine for about a month then died again, same fet and ic blown , so what i did is nicked the fet and ic (They were the same, pri) from the 12v side and replaced the blown ones (on the 24v side, pri) but tv would not switch on, this was because the second psu was not sensing the 12v, so what I did was run a wire from the 12v output on the main psu to the 12v output on the slave psu so the...
Leave a comment:
-
Re: Baird X47DTV power supply issues
Just thought I would throw this towards you Tom as I know you are on. The shitty job on the soldering is not infact on a mosfet, its on a leg of a transformer??
It looked to me like the mosfet but on closer inspection it was the tranny separating the primary from the secondary side. The tranny secondary leads to the 24v line.
I have done my best to solder it and it checks ok for continuity.
Could a badly soldered leg of a tranny cause the N channel mosfet to short?
Leave a comment:
-
Re: samsung 59" plasma pn59d6500df
Yep, They are 1080p . Got my 18n50 today, just waiting for the thermal compound. Enough of stealing thread, sorry Cash.
Added, I have no problem with the pic quality, just the same as the sony I had. Just the sound quality thats bad
Get some pics up Cash, Plasma Tom can then help aswel as the others here.
Same as in Baird or Panny?...
Leave a comment:
-
Re: samsung 59" plasma pn59d6500df
If what tom says it right (which it very much likely is) then the light flashing twice is just the set receiving power and then going into protection due to a fault.
Guessing by the post that you don't have this yet, ask a few more questions, or if its cheap enough buy it and lets have a look at the innards.
Also, Tom, if you can get to Hyde there is a 47" Baird, like the 2 I have here. Its on ebay and I have bidded on it, but if you want it then bid away as I can only bid so much.
Leave a comment:
-
Re: Post your system.......
Is that an ashtray on your table?...
Leave a comment:
No activity results to display
Show More
Leave a comment: