The value of R051 (R16051) is 5.6Ω. In my case I had to replace only R051 and Q051. Watching TV on this 2012 model... But I am going to hand onto my 2008 Panasonic
jet
Member
Last Activity: 08-07-2023, 06:24 PM
Joined: 04-12-2012
Location: Toronto
-
Re: panasonic TC-P50U50 8 blinks
The value of R051 (R16051) is 5.6Ω. In my case I had to replace only R051 and Q051. Watching TV on this 2012 model... But I am going to hand onto my 2008 Panasonic
-
Re: panasonic TC-P50U50 8 blinks
Edit.
I removed the large caps near R051 and I get a reading of about 27 ohms. I know another post say 6.2 ohms.Leave a comment:
-
Re: panasonic TC-P50U50 8 blinks
Need to bump this old thread.
My SMT resistor R051 has taken some heat and bubbled a bit, anyone know the value of the resistor?Leave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
Bump... How do I isolate the SC/SS boards from the A board, separately. When both are disconnected the PSU comes on. Want to narrow it down.
TIALeave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
Ok so I finally got back to testing this TV. I looked at the manual and it's not clear about the order of disconnecting SC/SS boards. Like what ribbon cable is for what board?
Anyway when I have all three ribbon cables disconnected from the A board and power disconnected from the SC/SS the fault clears. That is the red power LED come on solid no blinks.
How do I narrow down the boards to figure out if it SC/SS?Leave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
So what is the order of disconnecting the boards SC, SS and what cables do I take off power and the ribbon (signals) cable?
I will look at the manual too.
Thanks, JetLeave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
The 15VDC comes on when the power button is first pressed until the relay clicks and then the 15VDC disappears. So something is loading it I think.
What about the fact the the 3.3VDC is only 3.03VDC?Leave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
First off sorry for not getting back to this thread. My grand kids came over last weekend and I had to move the TV of the test bench... our bed in the spare bedroom LOL.
Anyway after long work week I now have some time.
I tested the TPSOS under the following condition. AC power not connected, then connect AC power. When AC is connect but TV OFF I get a reading of 3.03VDC on TPSOS (not a typo 3.03VDC reading not 3.30VDC).
When power On button pressed I hear the relay click and I get 0.0VD for a 1/2 second...Leave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
TPSOS appears to be labled TP3500 on the A board. It is +5VDC. Pin 7-8-9, P board comes on for 1/2 second or so at 14.65VDC. TP3500 stays at 5VD on.Last edited by jet; 08-26-2017, 12:22 PM.Leave a comment:
-
Re: Samsung LN48C630K1F no video.
I never did answer this thread, it was in fact the cap. TV work in now with 630V cap.
Leave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
Just looking for it now, where about on the A board is it?Leave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
More hopefully clearer pictures....Leave a comment:
-
Re: Panasonic TC-P50S1 with 10 blinks
I have added pictures of the A board because the manual say that is the board to look at....Leave a comment:
-
Panasonic TC-P50S1 with 10 blinks
Hi,
I have a Panasonic TC-P50S1 with 10 blinks SOS. I have attached pictures and some of the board part numbers are:
P Board = ETX2MM747AFK
SS = TNPA478
SU = TNPA4782
Am I lucky enough that the P-Board is subject to the thermal fuse failure? Here is to hoping I don't have to get into the SS board....
-
Re: Panasonic glass panel plasma TV? Model TC P50S1
daa OK got it now, glass expander. Gotta read closer LOL. Now I got to solve the 10 blinks will start a new thread when I get the back off.Leave a comment:
-
Re: Panasonic glass panel plasma TV? Model TC P50S1
RJ,
What do you mean glass expander?Leave a comment:
-
Re: Panasonic glass panel plasma TV? Model TC P50S1
Do you know what it would cost for the panel, is it reasonable? I bet the shipping is more that the panel LOL.
Also knowing it's tinted I could remove it , have a glass guy measure the tint and see if he can make a panel? Betting the original would have a special coating or something though.
I have not tried to polish it yet but I bet that would remove any coating too?...Leave a comment:
-
Re: Panasonic glass panel plasma TV? Model TC P50S1
Did you buy glass from Panasonic or aftermarket?
If I have to go to Panasonic should I go direct or contact a dealer to get me one?...Leave a comment:
-
Panasonic glass panel plasma TV? Model TC P50S1
Hi,
I download the manual found in post five of this thread.
[url]https://www.badcaps.net/forum/showthread.php?t=59159&highlight=Panasonic+TC+P50S1[/url]
Item 11 in the parts list is a "glass panel" item 4 is the "plasma display panel".
So is that correct is there a glass panel in front of the plasma panel. So if the glass panel is scratched I can replace it?
In general do all plasma TV's come with a glass panel in front of the plasma panel? I have never had to or tied to replace a plasma panel so... -
Re: samsung ln46a540p2fxza red light blinking
Got it going (no power cycling) now I have to fix the bad picture. I think I saw another thread here somewhere on that. Looking now.Leave a comment:
No activity results to display
Leave a comment: