Re: Samsung 226bw dead. No power
Just wanted to pop in and say thanks. I ran out of time for troubleshooting, so I ordered a logic board which came in today. Except for a slight flicker and a short buzz the first cold start it seems to work fine now.
Thanks for all your help, I´m less afraid to repair my own electronics now
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Samsung 226bw dead. No power
D701: 2.5 kOhm
D600: 154 kOhm
D603: 142 kOhm
This one was hard to get a reading on: 1.4 kOhm
I think you mean the BD600: 15.6 V
C639: 1.82V
The pins on CN400 read about 0.18V
I couldn't get a Voltage over this..
Again, thanks for the suggestions
Would replacing the logic board be a good fix then? I've read that the CCFL could easily give me another year's worth of use out of it....
Leave a comment:
-
Re: Samsung 226bw dead. No power
Any other tips on what I could try? I'm currently in doubt whether it's worth it to replace the logic board in a monitor that's been used quite intensively for 4.5 years, especially when it's uncertain if it'll fix the problem..
Thanks for your replies so far
Leave a comment:
-
Re: Samsung 226bw dead. No power
cn200
#1 : 0.01v
#2 : 1.82v
#3 : 1.83v
#4 : 1.82v...
Leave a comment:
-
Re: Samsung 226bw dead. No power
I´ve been a bit busy, but I just got round to measuring again.
With the power button, something weird seems to be going on. For starters, there was no proper grounding screw so I took the frame to which the button normally is grounded.
That aside, the voltages were very erratic. The only reading I got was on the one with the blue circle, which jumped around from 0 to 1.8V.
After this, I took the advice of measuring some testpoints on the back of the mainboard. The ones circled in red gave some odd readings and were...
Leave a comment:
-
Re: Samsung 226bw dead. No power
Thanks for the suggestions again: I just finished doing them.
Pin 1 reads 0.18V and Pin 9 reads 3.38V in both states
Pictures are attached. I'm not really sure how to measure the button. I took the grounded screw and measured the pins in the plug, which gave me a reading of 0 V.
Unfortunately he doesn't ship to the Netherlands. There are some Chinese sellers that offer it for $35, but if I can avoid it, I'd rather do it without the new board....
Leave a comment:
-
Re: Samsung 226bw dead. No power
Ah sorry, I thought selldoor just meant the power board.
Thanks for your effort so far ...
Leave a comment:
-
Re: Samsung 226bw dead. No power
I remeasured the power board and got the same readings as above.
I hope the pics are clear enough.
Please note: I made sure no wires or soldering tin is touching any other part. This might be unclear from the photo....
Leave a comment:
-
Re: Samsung 226bw dead. No power
When connected, I get nothing I'm afraid. Nothing on the LED and nothing on the screen.
Leave a comment:
-
Re: Samsung 226bw dead. No power
Just finished replacing those three, but unfortunately nothing happened. Anything else I can still try?
Leave a comment:
-
Re: Samsung 226bw dead. No power
Thanks for the response
I remeasured IC601:
17-33g
#1 = 0
#2 = 3.31
#3 = 5.19
So I suppose the fault isn't found in this part.
I replaced four bulging ones and two non bulging ones. I can't tell from the outside of the capacitors which brand they are unfortunately, but when I look at the site of my local electronics store, they only carry Panasonic ones for the type that I bought.
The ones I replaced are:
1x 330 uF 25 V 105 C
6x 820 uF 25 V 105 C
...
Leave a comment:
-
Re: Samsung 226bw dead. No power
Hi,
I stumbled on this page because my 226BW is showing the same problems as the poster. My screen started blinking/flickering as well and wednesday a week ago it finally died. The first thing I did was check the capacitors which were bulging, so I replaced these. Unfortunately, my screen still refused to turn on, not even the LED was blinking, so today I bought myself a multimeter and measured the same points as was asked:
On the power board :
1 - on/off = 0.18
2 - A-Dim = 0.14
3 - 13.5V = 15.64...
Leave a comment:
No activity results to display
Show More
Leave a comment: