Re: iMAC G5 PSU (again.. sigh)!
No code
No Test
Took your word for it (found it in the forum)
Thx
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: iMAC G5 PSU (again.. sigh)!
Well....
This is the first time I have used this part
So.. we will see if it does the trick
Will do load testing and see how this plays out
Have another of the same PSU model (and got a working delta)
What would you typically use for ZD6?
Leave a comment:
-
Re: iMAC G5 PSU (again.. sigh)!
Ok
Zener ZD6 - NXP BZV55-B16,115, Mouser P/N - 771-BZV55-B16115
Diode D2 - Fairchild FDLL4148_D87Z, Mouser P/N - 512-FDLL4148D87Z
Transistor Q1 - Fairchild MMBT2222A, Mouser P/N - 512-MMBT2222A
Thx
Leave a comment:
-
Re: iMAC G5 PSU (again.. sigh)!
Update
This unit had a bad Q1
I replaced D2 and ZD6 anyway
Replaced Q1 with a 350mW part
Seems to be ok again
Now... load testing
Any thoughts on using an ATX go/no go PSU tester
with the cables mapped to the Apple PSU?
Ok... before people start saying no; this is just for
future use with these PSU, before, that is,
I get my hands dirty
How would you handle 24V on an ATX tester
Leave a comment:
-
Re: iMAC G5 PSU (again.. sigh)!
Y - recapped the PSU
All of them except the main large can lytics for the primary and PFC
Someone had been there before me - did part of the job
Funny, post recap
Got the unit to start (with 15-16 jumpered)
Now it won't - very odd....
So will check Q1 and ZD6 - thx
Does the earth tag in the PSU need attachment to the PSU case?
It was not with this PSU
Will get the PSU right before the logic board recap
Will check the posts as recommended
Leave a comment:
-
iMAC G5 PSU (again.. sigh)!
Manu - AcBel
[url]http://www.acbel.com.tw/eng[/url]
Model - API4PC46
Apple P/N - 614-0326
System unit stuck on LED1
Will not start
Removed PSU, recapped
Tested PSU out of unit post recap
On standby
1 : +0.028 VDC (Black)
2 : +0.028 VDC (Black)
3 : +0.000 VDC (Black)
4 : +0.009 VDC (Grey/Purple)
5 : +0.000 VDC (Black)
6 : +0.009 VDC (Grey/Purple)
7 : +0.000 VDC (Black)
8 : +0.000/1 VDC PG (Blue) - swings between these two values
9 : +5.196 VDC...
-
Re: Harman Kardon AVI-100 Receiver
Thanks for responding
Well.. well.. well
Seems the IR is ok.
Did originally test this under flu tubes in the kitchen.
However...
This unit is going into protect at slightly high volumes say 9.45 - 10 pm
Odd.
I did check all of the O/P for main L & R out of cct. - these test ok
I replaced the O/P for the centre and rear - transistors and drive.
Maybe the speakers (small Sony midi hifi unit types) are difficult to drive
Unlikely as they...
Leave a comment:
-
HP ML150 G3 servers
Have an issue with CPU support on this
There are two mobos available
399971-001 410426-001 for earlier dual core only CPU systems
436356-001 436718-001 for later dual and quad core CPU systems
I have a 399971-001
This runs ok with 2 of Xeon 5050 (dual core) - 4 cores in total
Also runs ok with 1 of Xeon E5335 (quad core) - 4 cores in total
Will not run with 2 of E5335 - just hangs
All voltage LEDs read green
Have update to latest BIOS
Before I go any further with testing
1. What is the difference...
-
Harman Kardon AVI-100 Receiver
Seems to have issues with IR receiver (eye) in the unit
The part is a Hitachi TEMT5380 according to the service manual
Can't find these
This is a 38kHz part
Have been able to find a datasheet for TFMT5xxx - seems to be (newer) revision
These are TEMIC
Is TEMIC now Vishay or Atmel?
The remote commander control handset appears to be ok
Suggestions on a replacement for the eye
-
TASCAM Mixer
Hi Folks
Have a M-1016 for service, a cousin of the M-1024
Seems to be ok...
Bit old but still good
Need the service and/or user manuals
Tascam want 50 plus sterling (not a chance)!
eBay sellers want 10 sterling plus postage from Canada/US
for a photocopy!
Anybody got these and can eMail them to me?
Happy to consider offers
This has been placed on the Looking to Buy thread
[url]https://www.badcaps.net/forum/showthread.php?t=22789[/url]
Bump this thread please if in...
-
Re: Yamaha AX-430
Hi
2nd and 3rd pics on images0030.pdf show the switches
Leave a comment:
-
Re: Yamaha AX-430
Hi
Thx for responding
Ok.
The picture of the pot - second pdf only illustrates
the type of pot and mech. footprint I require.
Trust me, the damaged pot is destroyed beyond repair.
But where can I get the correct pot?
The leftmost three switches in the second pdf are damaged
The plastic blue material is the internals of each switch
A normal switch, black colour can be seen to the right
I know these switches are broken, they do no mechanically
work correctly. I have...
Leave a comment:
-
Yamaha AX-430
Rec'd this item as damaged.
The item has been dropped.
This is a project for the kids bedroom (when fixed).
The front panel source selection pcb has been broken.
It is only a single side pcb so, I should be able to repair this.
I am having issues however with sourcing replacement parts.
These include;
1. A number of source selector switches
2. A balance pot
There is a loudness knob missing on the front as well
as the Volume control knob. Both the pots and the
mech. fixings are in place though....
-
Re: Vestel 17MB18 Chassis
Thanks for the info
Have advised client, it would be best to prepare an
insurance report as unit is beyond economical repair.
I don't want to waste money stripping this unit to
replace lamps. It has damage to the LCD panel
(a scratch) and would realise little (if any) resale
value.
This is a really cheap TV. Client should be able
to get replaced with contents insurance.
May use parts for the purpose of testing CCFLs etc.
Thanks again
Leave a comment:
-
Vestel 17MB18 Chassis
Hi
Been some time
Have been passed a Dual DLCD2001 20 inch widescreen LCD TV for repair.
This experiences loss of backlight but has video and sound.
However, the odd thing is when I change channel or use AV, the backlight
will momentary come back on and go off again
Everything else with this set appears to be ok otherwise.
Anyway, suspected bad caps and found the usual suspects with
bad ESR. These were around the PSU and these have all been replaced
with Pana FM. Additionally, I found both of the only lytic caps on...
-
Technics Service Manuals
Hi
Can anybody help with Technics Service Manuals?
I live in the UK and have acquired;
1 of SL-P222A CD Player with optical O/P
1 of SA-GX200L Receiver
The CD player appears to be ok
I have serviced the decent Philips CDM4/19 transport
Will probably use a modern DAC with it, if it O/Ps S/PDIF - should do.
The receiver is only playing mono.
Appears the balance control is not working correctly
It is a bit scratchy - so deoxit or replacement
Any help appreciated
-
-
Server Backup & Storage
Looking for suggestions for HDD based server backup.
Considering options for a small network of 50 users.
Ideally, would want SATA HDD based backup unit to fit server.
Alternatively, would consider NAS with removeable storage
across LAN but suspect there may be bandwidth issues
Please advise
Thanks for your consideration
-
Replacement for KA5M0165R
Need this for a DVD/Karaoke open frame PSU repair.
This is a Fairchild part no longer in production.
The recommended replacement by Fairchild is a FSDM0265RN.
This latter part uses pin 5 whereas the former does not.
However, it appear for US import purposes (something
I will not be doing!) there is a court finding document
against Fairchild on the website prohibiting use of these
and other PWM parts as they have found to have infracted
the patents of a competitor.
Any help here as to a replacement?
Can't...
-
ID'ing a device
Cannot, for the life of me find a datasheet on a device I would like to ID
Any help appreciated!
Three pin device is marked as A 506 D13009K
Is this a transistor, MOSFET or what?
Cheers
No activity results to display
Show More
Leave a comment: