Re: I-Inc IF281D Display Problem
Thank You Very Much... Mockingbird. The Taicon 35v 33uf could very well be 5x11, it is C33 and part of the Primary PSU on the Board you referred to. I do not have any calipers to get an accurate Height and Diameter and have not removed any caps from the board, all done with a ruler in a awkward position. I will order up the caps. Thank you again for your time and effort.
dennylee
Member
Last Activity: 02-05-2012, 02:28 PM
Joined: 01-03-2012
Location: Washington State
-
Re: I-Inc IF281D Display Problem
PSU:
Taicon 50v 10uf "HW" 5x11mm 4 each
Taicon 35v 33uf "PW" 6x12mm 1 each
Taicon 10v 220uf "PW" 6x12mm 2 each
Taicon 25v 220uf "HD" 8x15mm 1 each
Rubycon 25v 680uf "YXG" 10x20mm 2 each
Chemicon 16v 1000uf "KZH" 8x20mm 2 each
Chemicon 35v 1000uf "KY" 13x20mm 2 each
Logic Board:
GJT 25v 10uf "M" 3x8mm 12 each
GJT 16v 100UF "M"...Leave a comment:
-
Re: I-Inc IF281D Display Problem
I believe you are correct...5mm.. eyes not as good as they use to be. I'm Game. I use to work on Arcade Games replacing chips in the 80's..would drop in a scocket for the next replacement..lifted a few traces in my day, lots of choice words would follow. The only thing that worries me is Taxes and running out of Wine
When I went to Badcaps to try and order all the caps I did not know where to find the caps I need. I have created an account however, is there somewhere else I need to be looking ? Mouser or DigiKey ?? I think I should replace the...
Leave a comment:
-
Re: I-Inc IF281D Display Problem
Logic Board has 20 Caps: 12 ea.--GJT 25v10uf (M) 3x8mm 105c
5ea.--GJT 16v100uf(M) 4x12mm 105c
3ea.--GJT 16v470uf(M) 8x15mm 105cLeave a comment:
-
Re: I-Inc IF281D Display Problem
To answer PCBONEZ...I did not keep the Box..it would cost almost $130 to ship...it is almost 3 yrs old. Bought another so this is just gravy and an attempt to hone some very old unused skills
Looking to Retire in Two years and need a hobby which might cover the grocery Bill. Pulled the Logic Board--identical to AloofOne INC so pic is posted of board....no physical damage: 20 GJT caps on the board. Will post values later.
Leave a comment:
-
Re: I-Inc IF281D Display Problem
My bad the hard tack was on the inverter board which has: 4 nippon 35v270uf 8mm x 15mm on them..I did get is off. The caps are on their side same as pic AloofOne posted. So far our monitors are the same. I have the PS out and on my Computer desk but have not pulled the Logic board.Leave a comment:
-
Re: I-Inc IF281D Display Problem
The logic board had nippon\chemi-con caps. On the PS: green Taicon for the:50v10uf, 35v33uf,10v220uf,25v200uf. Maroon nippon\chemi-con for the:16v1000uf,& 35v1000uf. Black Rubycon for the:25v680uf (yxg). Whew! Any suggestions on what to use to remove the sealant on the logic board caps ???? And this monitor was purchased directly from New Egg and shipped New to me not a refurb or a second so all caps from the factory... best of my knowledge.Leave a comment:
-
Re: I-Inc IF281D Display Problem
All info on the Caps including the yxg,ky,etc. wrote them down for each individual cap and posted it to the Mavens..not knowing the proper order to post I shotgunned the info. hoping you would be able to place it in the proper order. The Maroon 450v180uf is a Nippon/chemi-con but not being replaced. Ha...I see the symbols on the others will post later. ThanksLeave a comment:
-
Re: I-Inc IF281D Display Problem
No luck..on the Logic Board,Caps sealed down to Board,attempted to remove sealant and lost info underneath. I am more concerned with the power supply at this point...only 4 caps (all the same) on logic board IF I need to replace then I will release them and find a way to clean off the sealant, I can read 35v and a 0 on the end of the uf and that is all...Maroon in color. Humbly, I will start with the PS.Leave a comment:
-
Re: I-Inc IF281D Display Problem
Okay mockingbird, I will get the logic Board info....However this is a New Monitor which waranty runs out on Feb 5,2012. I broke the seal myself. Unless they replaced them at the factory I believe they have never been replaced. Anyway, better safe than sorry, I do not mind spending the bucks to replace all 14. I gave all info that is on the caps and I do not know how to tell who makes them usless it is by color. It would cost wayy to much to send it to Calif.. hence Cap repair. Thank you.Leave a comment:
-
Re: I-Inc IF281D Display Problem
also:89S---16v1000uf-105c(KZH)---1 each---8mmx20mm
C0839(M)-25v220uf--105c(HD)P--1 each---8mmx15mm
3M0822--Pet--25v680uf-105c--(YXG)--2 each--10mmx20mm
8(7) 9I---35v1000uf--105c--(M)ky---2 each---13mmx20mm
14 caps total I would like to replace. None show physical signs of damage, however, posts indicate failure. How do I order these from BadCaps ?Leave a comment:
-
Re: I-Inc IF281D Display Problem
I have been researching this Site for sometime and I have the same EXACT power supply as AloofOne However, it is in a Hanns-G. I would like to replace all the caps except for the Large 450v180uf. I am in Washington State, Here are the specs...please forgive how I give the Info.
C0823---50v10uf--105c(HW)p---4 each---5mmx12mm
C0837---35v33uf--105c(PW)P---1 each---5mmx12mm
C0841---10v220uf-105c(PW)P---2 each---6mmx12mm
89R-----16v1000uf-105c(KZH)---1 each---8mmx20mmLeave a comment:
-
Re: New Members - please post your introductions here
Hello, My name is Dennis( Denny) to friends and Family, I live in Washington State.
While using my favorite search engine..Dogpile.com looking for help on a Hanns-g 28" Monitor I came upon this site and decided to join. I picked up my AA in Electronincs at Lamar University, Beaumont,Texas after 8 years in the USAF in the Electrical Power Production Field. Electronics happened to be my weakest link and the G.I. Bill covered my schooling so off to school I went. Colecovision was my first Computer--besides the unit...Leave a comment:
No activity results to display
Leave a comment: