Re: 3 red blink in panasonic 65vt60
It is very difficult to find TXNSC1UCUUTH SC board
I only find in ebay one but it is in exchange to my fulty sc board.
I will have to pay two costly shipping +service repair.
The ss board is lass difficult I saw it in ebay for selling
I searched ebay and aliexpress.
Do you familiar a good place that sell good condition panasonic board?
Thank you.
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: 3 red blink in panasonic 65vt60
my sc board part number is TXNSC1UCUUTH
I managed*to find*another sc board*TXNSC1UDUUTH
visually they look the same
Do you know if they are interchangeable?
Thank you!
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
I took another reading when the ribbon of the SS board
Disconnected from the main board so the tv on with fan spining
The voltage on the Ss board stable
TPVE=149 VDC
TPVSUS= 200 VDC
This Is the highest I mesure is it low?
You mean the igbt need to mesure between legs
5000 ohms in the voltmeter screen the max I mesure
Was 590 ohms?
Thank you.
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
ן do another test disconnected also the ribbon cable of theSS board and tv click no red light, now green light and 2 fan spining.
The voltage Also stable
TPVE=149 VDC
TPVSUS= 200 VDC
Maybe the ribbon cable is not good?
Or it is a problem of the SS Board?
When conect the ss ribbon cable the tv red light flash
8 times and voltage on the 2 test point of ss board falling quickly.
Thank you very much!
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
I mesure transistors G C E
All of them is 570-590 ohms and 240-270 ohms
Between thr different legs but all is the same reading.
I find TPVE test point of SS board and TPVSUS of
SS board.
I isolated the SC board completely disconnected the ribbon cable and the Dc power connector.
Turn on TV and got 8 red light,
I mesure TPVE it start in 140 VDC and quickly drop to
0 VDC.
I mesure TPVSUS it start 140 VDC and quickly drop to
0 VDC.
Does...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
You are right The SC is malfunctioning for sure
But I also get 8 red light blink when conect the ribbon cable of the ss to the main board.
My understanding in electronic is low and I love this plasma tv so I am trying to repair it myself by replacing the fulty board with a working.
About the ss board I attached picture of the ss board and I mark the igbt I think you meant that need to mesure them for short?
How I mesure them there is three leg?
Thank you very much!...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
my mistake a frienf told me to mesure again the diode is ok, it is somthing alse that when i conect the ss board ribbon cable to the main i get 7 red blink
the tv turn on with fan if i disconect ribbon cable from ss and sc and from the C2 board data driver (lower center)
if this 3 ribbon cable disconected the tv on with click sound and the green light blink a few seconds and then the green lifht stay on, also the 2 fan spining.
no screen.
what board can cause this problem?
thank...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
I attach photo of*my ss board i dont know where*to find the*TPVE*or if there is one
I managed*to find diode that failed in the*continuity check*of my multimeter i measure it between the 2 legs and the multimeter*beef and i saw zero on the screen
I also check the power connector*of the ss board SS11 and no short*
Does it mean that I also need to replace the ss board because*of the diode?
Thank you very much!...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
The SS board give me 8 blink
The SC board give me 7 blink
If i disconect SS and SC ribbon and SC20 power cable the tv click and green light on and fans spin for 5 second
If also discoinect ribbon from C2 board data driver (lower center)
tv click and green light on and fans spin continuously.
Thank you very much!
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
HI.
I have diagnose and troubleshooting the tv:
There's a short in the SC20 Power Connector of SC board and a burn diode
I disconnected this Connector and the 3 red blink became 7 blink
After I also disconnected the ribbon cable from the SC board it blink 7 red code.
I disconnect the ribbon cable of the SS board and the TV suddenly starts to click and the green light blinks and stay on, the 2 fans and also spins for 5 seconds.
I then also disconnected the ribbon cable...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
I manegd to open the tv.
I accidentally forgot when troubleshooting to connect one little wire from the sub power to the large power supply.
I disconnected each board from ribbon cable and the sc gave me 8 blink and the ss gave me 6 blink.
When SS and SC board disconnected the tv turn on with click and then the green light blink and then green light fix.
This panasonic model TH-65VT60M.
I think SS and SC failure but I disconnected them and I thought that the 2 funs will...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
I remove the fulty sc board from tv everything is conected as should just without the sc board.
still the red light blink 3 times
could it be power supplay board or main board?
Thank you very much
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
I put the tv in scroll bar mode because*the tv is connected*to a pc and i wanted to prevent* burning on the screen.
all the 6.5 years the tv was connected*to pc for home theater*and i*occasionally use the white scroll*bar.
Before 3 days i open the tv and put 20 min of scroll*bar and suddenly i heard loud pop and the red light blink 3 times, now it is a summer time and the ambient temp is a little high in the house maybe the tv run a little hot but all the funs before the problem work wall as they do everyday.
...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
I check the buffers they are ok.
The sc board is dameged i saw there fry diode.
I tried disconnect*the ribbon cable and the dc cable from the sc board hoping the tv respond*but nothing happened*still 3 red light.
after I also disconnect*the ss board ribon cable and dc cable but still 3 red light.
i even disconect all the 4 ribbon cable from the main board ans also the dc cable from SS and SC board but nothing heppend the tv still blink 3 times red.
only when i disconect...
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
Another question*please:
When i check the buffer i need to do it without the*tv connected*to the AC main?
Thank you very much.
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
another qustion please:
how can i know that my power board is ok?
iknow for sure that the sc board is bed i saw a diode fry there..
my tv red light blink 3 times
Leave a comment:
-
Re: 3 red blink in panasonic 65vt60
Can I do this test when the buffer is inside the tv or must disconnect them from tv?
Also I need to disconnect the ribbon cable from the connector in order to drag the red lead on the connector?
Thank you
Leave a comment:
-
3 red blink in panasonic 65vt60
Hi to all the*members of this great forum I am a new member here.
I want your help please:
Yesterday I heard a loud pop and my plasma screen went black and the TV red light blinked*3 times repeatedly .
I opened the tv and saw a bed diode that exploded in the SC board and some of the transistors*malfunctioned .
The SC board number is*TXNSC1UCUUTH*.
I also see 2 boards connected*to the SC board (SU board*+ SD board)I can not see any visual sign of a malfunctioning but maybe there is a problem on them too.
I...
No activity results to display
Show More
Leave a comment: