Help
has anyone ever had this PC boots up but the display is missing moving the mouse or pressing any key help eventually pressing power button tto switch off 3 times it will display the welcome screen once login works until screen switches off due to power save then problem re appears.
popeye
Senior Member
Last Activity: 11-22-2024, 10:14 AM
Joined: 05-26-2011
Location:
-
win 10 no display at boot up
-
Re: Boardviews of some phones/tablets
what program opens these please -
Re: Boardviews of some phones/tablets
cheersLeave a comment:
-
Re: Where can i download .brd files for laptop can anyone guide me
just do a google search.Leave a comment:
-
Re: How Would You Service A Curved Led Lcd ?
The actual screen is flat.Leave a comment:
-
Re: Desoldering station vacuum pump. Looking for recommendations.
That looks like poor quality to me I have had a phillips model for getting on for 20 years just managed to crack it don't know why no spares for it now will have to buy a gun for one of the others that spares are available for just need to make sure about the wireing....Leave a comment:
-
Re: Desoldering station vacuum pump. Looking for recommendations.
I would recomend adding leaded solder to the joints you want to clear before desoldering keep the tips clear and you will not have them clogging so much.Leave a comment:
-
Re: Ipad 3 Mainboard Failure Help :L
You will need a stereo microscope to be able to see the very fine connections magnet wire for jumpers and a good soldering iron steady hands.Leave a comment:
-
Re: As19-h1g ic
Why not use chip quick?Leave a comment:
-
Re: CRT TVs
I am lucky I still have CRT sets in UK excerlent picture still sorry for you guy's in USA NTSC sets (never the same colour twice) the pal system is far better than any plasma crap or LCD orLED TV. Any poor sole that has a plasma set has never seen a good picture.Leave a comment:
-
Re: lamp tester
You can get a ccfl tester from ebay for very little money no need for a chassis.Leave a comment:
-
Re: Samsung TV picture is upside down! [HELP]
Wrog board for your screen update firmware to correct onLeave a comment:
-
Re: How do I spot a blown LED?
Light Emiting DIODE! how to test?Leave a comment:
-
Re: Help with how to replace LED's
My advise is to scrap the set you can replace the led strip with difficulty then you will find other leds go they can also be a fire hazard has I have seen bad burn ups due to these crap leds who ever replaces the led strip will be liable under law for any fire caused by their work do you have insurance that covers you for this type of liability.You have been warnedLeave a comment:
-
Re: how to read schematics
Have a look here look for basic electronics.[url]https://www.youtube.com/user/rossmanngroup/videos[/url]Re: how to read schematics<br /> <b...p/videos[/url]Leave a comment:
-
Re: Panasonic radio plays only one side
Hi I take it this is a stereo amp then you dont even need a schematic because all you need is in front of you check between the componant measurements
from one side of the out put to the other working one if your fault is not there check you are getting the correct inputs if in puts are ok then problem is with the ic if not you know what you should be getting from the working side so compare....Leave a comment:
-
Re: anyway to remove image retention or burnt image panasonic plasma
You could try injecting a pure white signal and leaving it on permanent may take some time to get betterLeave a comment:
-
Re: Calling all crt repairmen!!!!!
Leave a comment:
-
Re: Audio Power Output Module testing questions
The only way you can check the STK is in curcuit with vboltage supplied mesure the out puts and compare with the voltages shown on circuit dia.Leave a comment:
-
Re: is there any way to remove minor scratches on TV LCD screen
Leave the scratches alone I had one I scratched on a 50 samsung brasso just removes the black mat finish ang looks crap just leave it alone.Leave a comment:
No activity results to display
Leave a comment: