Re: Klipsch R-112SW manual
Someone?
Fripacks
Senior Member
Last Activity: 05-13-2024, 07:54 AM
Joined: 06-08-2021
Location: QC
-
Klipsch R-112SW manual
Hi, I have Subwoofer Klipsch R-112 SW , someone could tell me what's the value of Resistor 13 , it's just beside capacitor 1000UF 80 volts and is connect on Zener ZD4, I don't have service manual. -
Re: No picture LG model 50PT350
Hi,
thanks for your answer, I finally found bad solders on the YSUS board, now everything working fine!Leave a comment:
-
No picture LG model 50PT350
Hi guys,
I have problems no picture with LG model 50PT350, first of all, I change the 2 buffer boards who was no good, the TV working 2 weeks and today same problem, I check and I found Zsus board defect now, I change it for a new one and no picture, I check VS VA and 5 volts , all this voltage are there, I disconnect the upper buffer board, no picture, I disconnect the lower buffer board, no picture, what I have to check now?... -
Re: LG 55UB8500 no picture.
That's photo of TCON , I don't have schematic of the tv...Leave a comment:
-
Re: LG 55UB8500 no picture.
it have no backlight at firstLeave a comment:
-
Re: LG 55UB8500 no picture.
Do you have location number?Leave a comment:
-
Re: LG 55UB8500 no picture.
I check and they have 400 volts, on my first post I told I have voltages on the plug who's goes on Main BoardLeave a comment:
-
Re: LG 55UB8500 no picture.
Yes continuity no voltage on itLeave a comment:
-
Re: LG 55UB8500 no picture.
I check it and no voltage on this fuse, I think Main Board is the problemLeave a comment:
-
Re: LG 55UB8500 no picture.
Someone?Leave a comment:
-
Re: LG 55UB8500 no picture.
No picture with flashlight, no picture flashingLeave a comment:
-
LG 55UB8500 no picture.
Hi, I have problem with this LG model 55UB8500, it have no picture,I check voltage in Power Supply , all the voltages 24 volts 12 volts, 3.5 volts are there, when I push power ON, it have Red led on main board it stays red no blinking, on the power supply board when I put Power ON on connector P 802 LED + it have 48 volts on connector P 802 Led+ 48 volts, could you tell me what I have to check now? -
Paradigm Ultra Cube 10V2
Hi, someone have service manual or knows the value of the resistor in this subwoofer R43 and R47 location? -
Re: Toshiba TV parts Main Board 631V0G00520, it's for model 55LF711C20
Someone?Leave a comment:
-
Toshiba TV parts Main Board 631V0G00520, it's for model 55LF711C20
Hi guys,
someone could tell me why I can find Toshiba TV parts in Canada, I need Main Board 631V0G00520, it's for model 55LF711C20?Last edited by SMDFlea; 06-07-2022, 06:48 AM. Reason: Main Board 631V0G00520, it's for model 55LF711C20 -
Re: Plasma Panasonic TC-P42C2
The original board is TNPA5066AD, the new board is TNPA5066AC, do I have some adjustements to make?Leave a comment:
-
Plasma Panasonic TC-P42C2
Hi guys,
Hi, I have Panasonic model TC-P42C2 with Blinking led on the front, I found this TNPA5066AC SN Board defect, now the TV working with the new board but picture is very weak with blue color predominant and some horizontal lines, I check all the flat wires connections on the board and they ok, could you tell me if it's the new Board can cause this or the plasma panel is defect? -
Re: Yamaha RX-V3900
Someone?Leave a comment:
-
Re: Yamaha RX-V3900
I try disconnect all connectors on HDMI board always same problem, see the photos...Leave a comment:
No activity results to display
Leave a comment: