Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Another line came up for some reason. So after testing the ribbons by leaving the ribbons on and off I determine two ribbons that are the direct the cause of the line. Neither of them look like they are bad at least from the outside. One of the is attached to the logic main, and the other one is attached to the board to the right of the logic main. At this point is it worth replacing the the logic board and the other board....
jaysonfp
Member
Last Activity: 05-23-2020, 06:19 PM
Joined: 04-09-2020
Location: orlando, fl
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
You are not far from right in this one. If I had left ribbons unseated properly before with such a small margin of error I am sure it could be. Based on samsungs specifications and training there are 2 possible causes:
bad panel
bad logic board
connections
I would like to believe the logic board is fine since it allowed me to turn the panel on, and I just recently replaced it. I will verify the connections and clean them all out with alcohol....Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Are you sure is one of the ribbons on the lower buffer board? And not the ribbons in the logic?...Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
I replaced the logic board so I should invest time laying it flat again...Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
I had to adjust the screws in the y buffers and inserted them alll the way as far in and straight and the horizontal lines are gone but it appears the vertical line is still there. What do you suggest?...Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Also, if I seat the cables and is still like this could it be buffer boards or the y board being bad too?...Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Dick what about the vertical line you see there. I felt they were inserted all the way but I will take your advice and come back....Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Dick I made some progress. The main logic was bad, the new logic's led turned on instantly, and now I was able to turn on the tv but the image is having issues. I will give you great detail about what has taken place since then.
Once the main logic was replaced the tv still had no image. The light was blinking very slow with everything connected, and the voltages weren't right.
I took out the ribbon cable from the y-main that goes into the main logic, and the led in the main logic...Leave a comment:
-
Re: Samsung UN58H5202AF - killing mosfet.. no power
Sounds like the LED strips were bad....Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
I had to since at first I thought it was the power supply. Standby was getting the right voltage, and so were the rest of the pins going to from power supply board to main control board. Manual says to disconnect power to X and Y prior to jumping the power supply if I am not mistaken, to prevent damaging boards. The Y main in this tv connects to the X via a cable. The x connects to the power supply board via another cable.
Just got a notification that my replacement logic has arrived so lets...Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
So when I looked at the plasma manual for servicing this was the power on sequence:
1. 5V STBY SMPS to Main
2. PS_ON
3. PS_ON
4. VS_ON
Main to SMPS (all Low Voltages on) SMPS thru X-Board to Logic Board Logic Board thru X-Board to SMPS (VS & VA voltages turned on)
Next the 4. The same PS ON signal, (3.3V- 0V) is sent from the SMPS
CN804 connector to the X- Buffer Board and down to the Logic Buffer Boards to the Logic Board....Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Not blinking at all, read my previous post. I did get a replacement y board and buffer same issue. It appears to be main logic....Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Initially I suspected power supply but upon jumping the power supply board it actually ruled it out since the right voltages were read.
With power on, with either logic cable being removed from either x or y the same readings of 10 v on vs, and 0 va were read. It can't be both boards at this point.
This lets me know it is the logic main, or perhaps the main board....Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Left power on, and disconnected power to x n y board.
on the 200k settings of the ohmeter the results were the following:
60k for vs
52k for VA...Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Right now the tv is not turning on at all. I did jumper 3-4 on the logic board with all cables connected as normal. There were no test patterns showing at this moment. ...Leave a comment:
-
Re: PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
Thank you Dick tomorrow I will post pictures, I apologize if I lacked any information. I ended up doing a few things.
To test if the power supply is working I had to jump the power supply to PS-ON and Ground.
I tested VS at that point with X board and Y board disconnected to power.
VS tested at 211v VA tested at 57v which were the right specs attached to the tv.
I am thinking it is either the logic, or the main board so far....Leave a comment:
-
PN60E530A3F no picture, sound, getting 10v on VS, 0 VA
TV gets boot sound but no picture. Light in front flashes 6 times, then it gets the boot sound.
I had replaced y buffer, and y main. That did not get the panel to do get a picture, or boot. Suspecting power supply, main logic, or main control board.
I tested the connector from PSU to main controller board. The pins are getting the right readings for standby (5v), and the pins for that connector are reading the right voltage indicated on the board such as the 15v, or 5volts etc.
VS is reading 10v, VA 0v. Well below what it states in the tv... -
Re: New Members - please post your introductions here
I am new to here hoping to get assistance getting a tv up and running.Leave a comment:
No activity results to display
Leave a comment: