Re: Samsung 55H6203FXFA won't power up
Ok bad main board and possible bad power supply. Got it.
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Samsung 55H6203FXFA won't power up
# 12
"whats weird is at the test point j832 where it says 8v stb /13v on iam getting 11.5v and fluctuates to 10.5v in standby and 12.8v with tv on."
If i turn tv off voltage goes down to around in the 10.5 volt range then i watch the meter and it will rise back up in voltage with tv in standby.
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
Here are the pics requested. If they are too dark lmk....
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
"At that state when TV is off, the PS-ON is low and with main board connected the standby did go down below 10V, correct?" No the stand by is high @ 11.9v
"BTW, when TV is turned on, do you get switched 12V to the T-CON board?" No 0v to tcon board when tv is on ad fuse is good.
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
Also what could be the cause of voltage problems on OD and BLU. Thanks you are giving me great info.
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
Ok so if Ps/on is fine then should i be looking at the fact that power to the main board in standby is high around 11.5 and not 8v?
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
I believe the circuit involved for producing the 4.49v for standby on the power supply is damaged by the short and reads fine until the main board is plugged in and puts a load on it or i have a shorted main that loads up a good power supply. But should the main board have any activity on PS/On pin in standby that will cause it to be low?Last edited by tikalize; 01-17-2020, 04:21 PM.
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
Main board plugged in
OD= .2v On
0V Standby
BLU= 0v On
0v Standby
I dont know if it matters but the backlights are disconnected during these test or i hear arching....Last edited by tikalize; 01-17-2020, 04:08 PM.
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
whats weird is at the test point j832 where it says 8v stb /13v on iam getting 11.5v and fluctuates to 10.5v in standby and 12.8v with tv on.
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
iam getting
.2v @ ps/on with main board plugged in in standby
3.3v @ ps/on with main plugged in Tv on
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
Yes budm those voltages are with main boad unplugged.
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
I have seen the you tube video you have posted above. Maybe iam missing something but the main board i have dont have those IC regulator chips mentioned to test on this board. i have tried to find a service manual all over the internet. If i know what the voltages should be and where then i have a place to start. All the voltages match without the main board plugged in that of other posters with the same power supply but for some reason it seems like when the main board is hooked up it looks to me like there is an excessive load. Iam leaning...
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
tcon fuse has no voltage to either side and has continuity. (not blown)
Leave a comment:
-
Re: Samsung 55H6203FXFA won't power up
Sorry its UN55H6203AF....
Leave a comment:
-
Samsung 55H6203FXFA won't power up
I stated testing this unit and I had no backlights but I can see a picture with a flashlight to the screen. I started testing voltages at the 10 pin connector on the Power supply board (BN44-00774a) where the main board harness plugs in but and I accidentally touch 2 pins together (I believe it was pins 7 (13volts) and pin 9 (ground) Now I have no picture and no led on t con board. The red standby light come on and I can see the optical red light also illuminate. The backlights were shorted and was my original problem but now I cause this problem.
Voltage is as follows on these...
No activity results to display
Show More
Leave a comment: