I have a Samsung TV that has a bn94-07217N main board. I am having a hard time finding the N version of the board but I can find Ver K and Ver F boards. Does anyone know what the differences are and whether they are interchangeable?
I was told that the N ver is a Canadian version.
If anyone has any information on the Samsung versions it would be appreciated.
PMan976
New Member
Last Activity: 05-25-2024, 10:22 AM
Joined: 01-04-2020
Location: Dawson Creek/ BC
-
Samsung Main board replacement-bn94-07217N
-
Re: Sony STR-DE335
I replaced both IC 701 and 702 and still the same. It might be going to the trash heap soon.... -
Re: Sony STR-DE335
I found the 12v regulator problem, I found that I forgot to reconnect one connector CN5702 . I now have all my voltages 12v +and - ,5v, are all good now.
I checked IC 701 and 702 and yes it appears bad , I have high voltage on almost all of the pins on both IC's Now I have to get replacements before I can move forward....Last edited by PMan976; 03-27-2022, 07:36 PM.Leave a comment:
-
Re: Sony STR-DE335
Yes, the emitter resistor are R616, R766, and R666 and R716.
I get on Q604
B= -44.7v
C= -76.2v
E= -44.2v
I get on Q754
B= -45.2v
C= -76.4v
E= -44.8v
Q 501,701,702 appear fine.
While checking out the answers to your question, I found I am getting -12v on IC802 but not getting my +12v on IC801, and my 5v line is only 2v but as it is fed by my +12v it is to be expected. I am not getting my B+( 18.1v)for my +12v Regulator. I will take some time and...Leave a comment:
-
Velodyne DLS4000r Parts ID
I wonder if anyone could help. I am troubleshooting a Velodyne DLS-4000r that has no audio out. I traced the audio to the PA board and I get it to the C4 Cap, and nothing on the other side. I am trying to identify the value of this cap so I can replace it and see if that solves my problem. Maybe more wrong with this, but that is where I am starting. Does anyone know the value of C4 in PIC?... -
Re: Sony STR-DE335
Thanks for the input. I tested all of the Transistors and the resistors and they are all within spec. I also went through all of the solder connections to see if there were any cold solder joints, and there weren't any obviously bad ones. I resoldered all of them anyway to be safe. I found it odd as well that all of the resistors show high voltage. I found a service manual for this unit and will dig deeper ( available here if anyone wants a copy- )Leave a comment:
-
Re: Help diagnosing Pyle Receiver PTA66BT with burned resistors
Thank you budm, I replaced all of the blown transistors and also upgraded the Resistors to 3 watt. The unit is working great now. Your input was most helpful.Leave a comment:
-
Sony STR-DE335
I have a Sony STR-DE335 that keeps coming up with "PROTECT"
I checked the center pin on all the Emitter Resistors and they all show a high voltage ( 46vdc ) and I know they should read low-voltage. I have been searching and searching for bad components and I haven't found any yet. I tested all of the output transistors and they all appear fine. Any help with this would be appreciated. I should also add that when I was testing , I accidentally blew the 12v regulator before I discovered that the unit would power up with no " PROTECT " error and all of the voltages on the...Last edited by PMan976; 03-18-2022, 10:55 PM. -
Re: Help diagnosing Pyle Receiver PTA66BT with burned resistors
I tried following this as best as I could and I am probably missing something.
I have a unit that has the exact same issue with that resistor burned up. Does anyone happen to remember what was the cause?Leave a comment:
No activity results to display
Leave a comment: