Hello i have this notebook Asus X550ld they work normal but the image appears with interference (like video attach) i have try, New lcd and a new cable, but unsuccessful if i connect to a external monitor the imagem in the external monitor is normal without interference, any help?
Thanks...
vabea
Member
Last Activity: 04-12-2025, 04:53 AM
Joined: 12-05-2019
Location: porto
-
Hi, i have try this and work again.
[URL="https://www.badcaps.net/forum/showpost.php?p=1062313&postcount=53"]https://www.badcaps.net/forum/showpo...3&postcount=53[/URL]
ThanksHi, i have try this and work again.
[URL="https://www.badcaps.net/forum/showpost.php?p=1062313&postcount=53"]https://www.badcaps.net/forum/showpo...3&postcount=53[/URL]
ThanksHi, i have try this and work again.
[URL="https://www.badcaps.net/forum/showpost.php?p=1062313&postcount=53"]https://www.badcaps.net/forum/showpo...3&postcount=53[/URL] -
you are right, i dont want risk dameged the board with this cable.
But this is the second cable i buy, and have the same grounded pins, i will try to find one with the same reference.
Thanks for the helpLeave a comment:
-
With the cable connected the lcd work fine, only stop charging.
And if i connect only the cable the other side not connectd to the lcd and webcam, they stop charging too.
With the cable connectd they power on only with the battery connectd, with the power adapter the led blink 3 times and dont power onLeave a comment:
-
i use pin 74 (ADP_DET) in the U13, because is the same side of the board (more easy to me) and i have 1kohm, voltage in pin 5 are 3,29v.Leave a comment:
-
I have put a piece of tape in pin 37 cable, is the same thing no?Leave a comment:
-
Ok, thanks for the help, i will try to find another dealer and by another cableLeave a comment:
-
Thanks for the help, is that why it dosen't charge?
I covered the pin 11 in the cable with tape and dont't charge.
The pin 37 is shorted to groud too, i put tape but still not charging,
if i unplug the cable they charge the battery normaly, i don't understand whyLeave a comment:
-
CN2
The L23 near the lcd conector burned too, i have shunt. and image work againLeave a comment:
-
Hi, i don't have the original cable to compare, i only compare the gnd pins between the cable and board connector, the pins i refer in the cable (11,15, 18, 31, 37) are shunted
In the connector the gnd pins are 12, 15, 18, 21, 31 and 34 different from the cable
attach boardview.
thanks
[COLOR=#8e44ad][B]Link to schematic /Boardview[/B][/COLOR] [URL]https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/schematic-requests-only/79201-hp-probook-450-g4-da0x83mb6h0-boardview-or-schemat...Leave a comment:
-
Hp probook 450 g4 - Don't Charge
Hello my client tried to change the screen by himself, and he connected the cable incorrectly and burned the screen and the cable, i have change the screen and by a new cable and the notebook work fine, but they dont charge the battery, i have made this experience, i disconect the lcd cable from the board and notebook work and charge normaly, only when the lcd cable is plugged (only pluged on the board, not conneted to the lcd) they dont charge.
My original cable have the refª dd0x83lc720, i by in aliexpress the refª dd0x83lc810 the dealer told me is the same, in the new cable the pins... -
Hello, i have the hp probook 450 G4, power on, but no video, any one help me clean me?
Model : Hp probook450 G4 (DA0X83MB6H0 Rev: H)
Model: X83:
S/N: 5CD6518Q36...Leave a comment:
-
Re: LG 32LF510B - EAX66453203(1.0) Need Firmware
This is the datasheet i used...Leave a comment:
-
Re: LG 32LF510B - EAX66453203(1.0) Need Firmware
Hi, i have found, but still not power on, i have all the tensions on the board so any idea what could be the problem?
If any one need a attached the firmware...Leave a comment:
-
LG 32LF510B - EAX66453203(1.0) Need Firmware
Hello i have a lg 32LF510B ( EAX66453203(1.0)) that dont power on, only power led lights up continuously
i want to reflash firmware to test, so if any one have i apreciate
regards -
Re: Toshiba Portege Z30-A
Ok, thanks,i have try again with the new configurations but in the tl866 only read "0" in the ezp2013 (i select the chip Winbond "w25q128"), read some data, can verify if is correct?...Leave a comment:
-
Re: Toshiba Portege Z30-A
I dont use the clip, i have remove the chip before read, the only think i use is the 1,8v adapter, the programer read without erros but empty, i want to try other bios to test but before i need to backup this.
maybe the bios is realy empty, could be possible?
I power on the pc, and the lights power on but no image, after a few seconds they automaticaly power off and i power on again and they work normaly, other think is that, they dont detect the wireles lan and the official bios utility dont work.Leave a comment:
-
Re: Toshiba Portege Z30-A
I have measured the voltage in pin 8 when the notebook is power on, and i have found 3,3v,maybe this why the readers dont work?...Leave a comment:
-
Re: Toshiba Portege Z30-A
Thanks, is that possible? because the laptop boot, not in a correct way but they boot, i have try several times with two programers same result...
i dont want risk erase and put a new bios i´m afraid to demage the bios...Leave a comment:
-
Re: Toshiba Portege Z30-A
hi, in other post SMDFlea, say that this bios is compatible with winbound W25q128Fw1,8v, so i have try read this bios (attached) and i think is blank can any one verify, i have soldered again to the notebook and a 3th try they boot, can any one verify?
Thanks...Leave a comment:
No activity results to display
Leave a comment: