Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Lenovo Yoga 370 LA-E292P no power on VCCCPUCORE, VCCGFXCORE_I, VCCSA
Hi everyone, having LA-E292P on a desk, there was some light corrosion around PU137 (NCP81218) - cleaned with fiberglass pen + ispropyl alcohol. All basic rails are ok (3.3, 5, 1.2, 12 , charging ok), except the VCCCPUCORE, VCCGFXCORE_I, VCCSA. All these are driven by NCP81218 + 3x NCP81382, HIGH state on CPUCORE_ON, but LOW on DRVON which enabled those 3 NCP81382. Tried to connect 3.3V from CPUCORE_ON to DRVON, but measured LOW after this. Resistance between those rails and GND are 6 / 9 / 19 ohms. Any suggestion what else to check. Thanks1 Photo
-
Re: PCB USB to SATA
Check this - [url]https://forum.acelab.eu.com/viewtopic.php?f=156&t=10708&p=39001[/url]Re: PCB USB to SATA<br /> <br /> C...&p=39001[/url]
-
Re: TP-LINK TL-GS1016D ver 8.0 burn
I bought same switch, but Ver.11 and it looks completely different... Whatever, will put an order on Ali to get the ICs, and use some step downs to test. Will be a pain to solder/check that TQFP-216.
At least SPI EEPROM is readable, and there isn't anything else to be broken....
Leave a comment:
-
Re: TP-LINK TL-GS1016D ver 8.0 burn
I said, don't askI forgot to connect step down 48->12 between battery and devices. Also Synology DS923+ died... That's when one used same connectors on both sides. Not the opposite polarity, but 4x voltage
...
Leave a comment:
-
TP-LINK TL-GS1016D ver 8.0 burn
Hi all, I've been using external 12V PSU for this switch, but mistakenly connected it to 48V. Better do not ask howI'm going to rescue it, will replace both chips (shorted to ground), but both switching controllers were burnt as well.
3.3V controller unreadable, SOT23-6.
1.1V removed and forgot to note the remaining markings
Anyone with same switch available to check? In a worst case, I'll use 2 step-down modules instead... Thanks...
-
Re: Transfer Windows-Key from bad BIOS to new BIOS
Quite old topic, but any progress - maybe different topic? I've got DELL Optiplex 9020 with physical sticker and would like to "transfer" it into BIOS
Leave a comment:
-
Re: LA-H131P ideapad s340 no power
Have you moved on with this?...
Leave a comment:
-
Re: Lenovo E480 NM-B421 need schematic or BV
Thanks, find it useful when trying to understand whether USB-C port is directly connected to 19V rail.
Leave a comment:
-
Re: Bdl50 la-0704p dead
Hi, having the same board on a desk (i5-6200U), with same issue. Let's inject more amps, I've used ~3A to have ~4W for dissipation, then you can identify source easily. In my case it's smaller die on a CPU package. Strange that is probably third board with 6th Gen Intel with same issue.
EDIT: also have short on +1.0V_PRIM railLast edited by tahc81; 03-08-2022, 04:38 PM.
Leave a comment:
-
Re: HP 250 G7 EPW50 LA-G07FP Schematic
Having one on my desk right now, so the schematic is really appreciated
Leave a comment:
-
Re: Asus F555UB i5-6200U - HDD not detected
So, after long waiting, connectors have arrived, so I've replaced one on a motherboard. Voila, HDD detected, audio detected and working. Thanks for suggestions.
Hot air from bottom side + micro soldering tip from top side to finish it....
Leave a comment:
No activity results to display
Show More
Leave a comment: