dysk1
Member
Last Activity: 03-26-2025, 01:31 AM
Joined: 08-27-2019
Location: Tychy
-
After replacing the balls under the processor, the laptop works on the day of release. -
I noticed that if the laptop flap is closed then the laptop turns on much more often. The flap can then be opened and the system works until it shuts down. Later, with the flap open, it is virtually impossible to turn on the laptop....
Leave a comment:
-
Hello,
I have new information, As I turned the laptop on and off a few times, the laptop turned on twice. But the laptop doesn't start up again....Leave a comment:
-
Asus vivobook PRO 15 M3401QC - no power
Hello,
Asus vivobook PRO 15 M3401Q
Mainboard:M3500QA R2.1
CPU:R7 - 5800H
GPU:GN20-P0-A1 RTX3050
S/N:N3N0CX130356102
The laptop charges, when you press the “Power” button, the LED's of charging and working of the laptop light up. No image on the matrix as well as HDMI. After disassembling the laptop I took the first measurements, the results are shown in the photo.[ATTACH=JSON]{"data-align":"none","data-size":"full","title":"Asus M3500QA R2.1.jpg","data-attachmentid":3493469}[/ATTACH]... -
HP EliteBook x360 1030 G4 DAY0PAMBAF0 REV F Request to identify items
Hello everyone,
I have 2 components on the board torn out I think, can someone help me identify them.... -
Hi,
are you able to help me with this topic?
[url]https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/bios-requests-only/98736-thinkpad-e480-bios-dump[/url]https://Hi,<br /> are you able to he...ios-dump[/url] -
Hi,
are you able to help me with this topic?
[url]https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/bios-requests-only/98736-thinkpad-e480-bios-dump[/url]https://Hi,<br /> are you able to he...ios-dump[/url] -
Lenovo E480 NM-B421 please repair the bios
Hello everyone,
I bought a damaged laptop, one RAM slot was not working. I thought it was the Bios fault, so I uploaded one from this forum, unfortunately the laptop did not turn on anymore. I uploaded the original bios back, but the laptop no more turns on.
The laptop is charging the battery, 3V and 5V are present. After pressing the power button no reaction.
Attached is the original bios and all data. Please fix the bios....Leave a comment:
-
Re: Marshall Stanmore II voice with the google assistant built-in
3 out of 5 speakers were repaired.
The first repaired after several reset attempts.
In the second one, I found a capacitor short-circuited.
In the third, I found a damaged resistor.
I have not fixed the fourth one yet, based on the current consumption and the thermal imaging camera, I can see that the linux itself is loading but it probably does not execute the program.
The fifth play is still ahead of me.Leave a comment:
-
Re: Marshall Stanmore II voice with the google assistant built-in
The reset procedure is like this: "Press and hold both the Source button and the play/pause button for 7 seconds," but it doesn't do anything. I can't see the UART, but there is a USB service port. I opened this FS5332 and made an overview shot. All voltages on the board are correct.
Located layouts:
88DE3006-BTK2 Marvell
NT5CC256M16EP-DI Nanya
88W8887-NAA2 Marvell
TC58NVG2S0HTAI0 TOSHIBA
Unfortunately, I have nowhere to get a working speaker. The...Leave a comment:
-
Marshall Stanmore II voice with the google assistant built-in
Hello everyone,
I'm Marek and I'm from Poland.
I bought on our auction site 5 pieces of damaged Marchalla speakers. I'm an electronics engineer and thought I would fix them myself. I was very disappointed with the construction inside.
As power amplifiers there are 2x TAS5711. Everything is controlled by a ready-made module from Frontier Silicon MINUET FS5332. In the attachment I send pictures of the PCB. All 5 pcs have the same fault. The power supplies have 24V at the output. After connecting the power supply from the lab power supply, you can see how the current floats... -
Re: Marshall Stanmore Repair
LM317 had the same protector signal as the inverter. After desoldering another resistor all voltages have already appeared correct.
Unfortunately, no functions are still working.Leave a comment:
-
Re: Marshall Stanmore Repair
Update:
What voltage should come out of LM317??Leave a comment:
-
Re: Marshall Stanmore Repair
A larger picture is attached.
Edit:
I measured that instead of 3V on TAS5508C power supply I have 0.6V...Last edited by dysk1; 09-03-2019, 08:42 AM.Leave a comment:
-
Re: Marshall Stanmore Repair
Hello,
I also have a device that doesn't work. After switching on the power supply instead of 30V I have 8.3V.
I drew a converter feedback diagram. I came to the fact that it blocks the signal fed from the 12LE5A16S2 processor to the R147 resistor. After desoldering the R147 resistor, the inverter works correctly and has 30V, but this is not the solution to the problem.
I am asking for any suggestions.
[url=https://naforum.zapodaj.net/8b2e6e228288.jpg.html][/url]Leave a comment:
No activity results to display
Leave a comment: