Hello,
Thank you. I try with your file and allways black screen.
Maybe it's a hardware issue... I check Ram, screen without success.
I thought that when the keyboard had the LEDs working but no image, it could come from the Bios but I may have been wrong.
Thank you for your help. If someone have an idea, that'll be very appreciated....
kurtspirit
Senior Member
Last Activity: Today, 01:08 AM
Joined: 02-09-2019
Location: Toulouse
-
Hello,
Sorry.
Here is the serial number : LANRKD005516441Leave a comment:
-
[REQUEST] G512L Error NeoProgrammer
Hello,
I'm getting back to you because I have an error that I can't understand when trying to recover an Asus G512LV that boots but no image.
I downloaded the version from Asus and I simply wanted to inject it directly to see if it could give a sign of life to then try to correct the Dump file but when trying, NeoProgrammer returns the error: neoprogrammer "buffer size not equal to ic size".
I don't think I'm dumping the wrong chipset because I have the Windows key in it but it's true that the original Asus file is not the same size as the IC...... -
Hello,
Thank you for your reply.
I inject to a diode near this one. I try to the coil but nothing happened.
Thank
Leave a comment:
-
AN515-51-56G8 Help to indentify an IC please
Hello,
I have an ACER NITRO computer that no longer starts. The power supply is ok, the charging light is present (but flashing - potentially the battery is out of order) but if I try to start it, nothing happens. I injected 1V 2A on the board and saw an IC that appears to be a power supply controller that is heating up.
So I'm trying to find out what it is. The marking is: BAA70N or BAA7ON. Do you have any information on what it is or an equivalence please?
Thank you so much...
-
Ok, i knew for the dot but not the side
So , pin 3 is 1.60kohm and 13 : 0.01ohm.
Thanks for sharing your knowledges and your help.Leave a comment:
-
Hello,
Thank you.
Here are results :
Pin 3 : 8.7 kohm
Pin 13 : 10 kohm
I followed the datasheet to find the pins, at least, the direction to read them. If I'm not mistaken, they are in the "counter-clockwise" direction but if I reversed it, then here is the result:
Pin 3 : 1.60 kohm
Pin 13 : 0.01 ohm.
To be as clear as possible (I apologize for my low level of knowledge), I add to the message a photo with the measurements indicated according to the pins.
Thanks again....Leave a comment:
-
[REQUEST] Tuf 517Z not turn on.
Hello,
I am looking for this component please : the mark is 5X = 9C 909
The PC is a TUF517Z and the fault is: no boot.
The charge seems ok although the orange light sometimes starts flashing but no boot.
This happened after an object fell on it.
I put the CM under a thermal camera and this famous component directly rises in temperature. So I assume that it is responsible for something.
Do you have any idea what it could be please?
Thank you.... -
A2141 Jack audio issue
Good morning,
I have a problem with a Macbook A2141 with the audio jack port. Sound only comes out from one side (left). The right one just emits a kind of crackling sound.
I changed the jack ports twice to be sure that it was not caused by a defective part, but the result was the same.
I have the impression that it could be an audio filter or component but I am unable to locate the affected part on the motherboard.
Have you ever encountered a similar problem and can you help me find the filters, if they exist, on the map please?
Thanks in advance... -
Hello,
I have a HP X360 11 G5 EE with a corrupt bios (if i trust in HP : blinking 2 long - 2 shorts)
I try to recover it with an USB key and Windows + B on keyboard without success.
Here is the dump , i'll put the latest bios update from HP too.
Informations from this laptop :
ProdID : 40P1EC#ABF
SN : 5CG131190Q
Can someone help me with a new bios image ?
Thank you very much....Leave a comment:
-
Re: LENOVO G50-70 Bios Password
Thank you very much. I'll try to find how and where is the DMI area. If someone else can help, that will be fantastic !
Thank again...
Leave a comment:
-
LENOVO G50-70 Bios Password
Hello,
i hope i'll be ok and not against rules with my request.
So i have a Lenovo G50-70 , S/N : YB08544882, MB model : ACLU1/ACLU2 Rev 1.0 with Bios Password locked.
I try with autopatcher and the result is : "Dump.bin is corrupted or does not contain a valid dump".
I think my model isn't compatible and some skills missing me to remove the password by myself.
Can someone help me to do that please?
Thank you very much....Leave a comment:
-
Re: [REQUEST] Asus S413DA battery connector : Pads issue
Hello,
All is allright now. You're right, the pads wasn't importants.
Thank you.Leave a comment:
-
Re: [REQUEST] Asus battery connector : Pads issue
The card works well on the mains, the PC shows no other signs but perhaps the problem comes from the load management chipset?
He changed the battery with an original manufacturer because the previous one no longer worked.
Why have a blue wire on the battery and not a blank like on the other side if there is no connection?
Do you know what this thread represents by any chance? It's just for my personal culture
Thanks again.Leave a comment:
-
Re: [REQUEST] Asus battery connector : Pads issue
Ah yes, I feel stupid for one out of the two... Indeed, the first from the left is not connected, on the other hand, the one on the right is on a blue wire on the battery side.
I tried before desoldering everything to connect the battery without these pads and it does not work.
I wonder if it's not connected to this track but I wouldn't want to do that randomly.
Thank you for the answer...
Last edited by kurtspirit; 09-08-2023, 10:48 AM.Leave a comment:
-
[REQUEST] Asus S413DA battery connector : Pads issue
Good morning,
I have a friend who dropped off his Asus just now. He tried to change the battery but tore off the connector.
I can catch up on both tracks but I'm missing two pads that don't have visible tracks to bridge.
Can you help me please ?
Thanks in advance.
The laptop is a S413DA , i don't find any boardview.... -
Re: TUF505DT : No charge
To be honest, I don't know.
I think a Mosfet (I changed them all) caused this broken line but that's really a guess...
The previous battery had suddenly stopped charging for no reason, that's when something happened but it will remain a mystery.
I changed in the end: battery, the 3 Mosfets, the charging IC, a diode.
Thank you very much to everyone anyway, it's a pure pleasure to see the PC working again!Leave a comment:
-
Re: TUF505DT : No charge
How to thank you?!
The PC is finally charging! I'm so grateful, I never thought I'd get there. It's awesome ! I'm really happy and thank you ten thousand times
Leave a comment:
-
Re: TUF505DT : No charge
Ok mon2, now the resistance is about 0.01ohm. Maybe i have to test with battery ?Leave a comment:
-
Re: TUF505DT : No charge
The trace is clearly cut. I'll put a wire instead.
For the pics, i'm sorry but when i use the link from forum , pictures doesn't appear in the message...Leave a comment:
No activity results to display
Leave a comment: