Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Retested the Cathode and TPSOS7. Got 5v on both.
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Anode .3
Cathode .2
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Getting 15v there.
That thing is super small. Hard to get a reading but it gave me 3 for a split second and then went straight to 0.
Weird new symptom. Before when I started it up it would click, SOS7 twice then turnoff. Now it just stays on and does the SOS7 over and over. Not sure if that has any meaning....
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Should I test the diodes?
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Tested them:
VSCN 40
VSUS 198
VAD 185
Manual says that's right where they should be....
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Adding photos of the TV....
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Hi tvtimmy, yeah, just did again too to make sure and still same result. Clicks, LED comes on, flashes 7 times and turns off....
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Now I know tvtimmy stated that those plugs I circled in my picture above should be fine but is it possible that they are messed up which is why I'm getting the 7 blinks? I'm thinking its the SU/SD boards but I just don't know.
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Went through and reseated all the ribbon cables and tightened all screws, then tried jumping it but received the same 7 blink code.
I actually thought it was the power supply at the very beginning and so I purchased a new one since they were pretty cheap but it turned out to be something else. I did check the transistor on the new one though and those came back good....
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Attaching manual....
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
So I tested my old SC board against my new SC board and have discovered that all the transistors on my NEW board are good but Q441 on my OLD board is shorted. So I at least now know my old SC board is bad.
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Q661 does not show a short.
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Ok there is no beep.
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Ok, I grounded to a screw hole with black and test both SC2 probes with red and one of the SC 2 probes has a continuous beep.
Leave a comment:
-
Re: Panasonic TC-P50G10. 6 blinks to 7 blinks.
Ok tested the pins of the ribbon connectors and no beeps. Should I also be testing the needles circled on the picture I attached?
...
Leave a comment:
-
Panasonic TC-P50G10. 6 blinks to 7 blinks.
My Panasonic recently went out and had a 6 blink code. Per the manual, 6 blink code means SS, SC, SU or SD board. It turns on, shows no picture blinks 6 times then turns off. I read the most common issue is the SC board so I purchased one and switched them out but the TV went from a 6 blink code to a 7 blink code. The manual states that is an issue with the SU SD or SC board. I'm wondering why it went from 6 to 7. Did I buy a bad SC board or is it just the SU SD? Is there any tutorial I can use to test the SC board? I have a multi meter but pretty new to this stuff.
-
Re: New Members - please post your introductions here
hello from Texas. New to all of this and hoping to learn something from you all.
Leave a comment:
No activity results to display
Show More
Leave a comment: